Separate the wires between the original indicators and the wire connectors from the wire loom at a suitable position. This avoids interfering
with the original wire loom. Find the circuit diagram to the original wires in the wire loom for your bike and connect them to the micro 1000
LED / LED white / Dark / Extreme as follows:
• Connect the grey wire on the left-hand (or right-hand) micro 1000 LED / LED white / Dark / Extreme to the plus pole on the left-hand
(or right-hand) indicator.
• Connect the black wire on the left-hand (or right-hand) micro 1000 LED / LED white / Dark / Extreme to the minus pole on the left-hand
(or right-hand) indicator.
Crimp connectors and shrink-on tubes are part of the shipment. They will connect the wires of the indicator with the wires of the original plug.
First push one of the shrink-on tubes over one of the cables you want to connect and remove fi ve millimeter of insulation on the end of each
cable. Then push both uncoated ends of the wires into a crimp connector and then crimp it with an appropriate tool. Then pull the shrink-on
tube over the connection and heat it up equally until it fi ts tight over the complete length.
This type of connection is technically permanent. To create a non-permanent connection, we recommend Posilock wire connectors (not
included), which are available for purchase from our website at
www.kellermann-online.com
(Order No.: 123.955 / 123.956).
Arrange the wires to protect them from splash water and fasten them as appropriate, such as with wire connectors. Now test the micro 1000
LED / LED white / Dark / Extreme lights. This completes the installation.
Refer to our homepage at
www.kellermann-online.com
for our additional information, and our online shop with a full range of spare
parts and accessories and a download area. If you have any suggestions or questions, please do not hesitate to contact us by eMail
(
) or phone on +49 (0)241/9 38 08-0.
INDICATOR FLASH RATE
If, after installation, the fl ashing frequency should increase to an unacceptable degree (some original fl asher relays only function with original
electrical fitting) or if, instead of two, all four indicator lights light at the same time, we recommend the following solution: Use a load-
independent Kellermann relay (Article. no. 123.970). This solution is preferable because it is simple, safe and reliable and can be implemented in
a short time. If you cannot use this relay with your vehicle, you can also install power resistors that can be connected parallel to the indicators.
Attach the resistors in such a way that the heat can adequately discharged. The required ohm for the resistors is variable according to the
vehicle; for original indicator lights with 21 W, one resistor with e.g. 7.5 ohm and 50 Watt capacity per micro 1000 LED / LED white / Dark /
Extreme will be effective.
If you contact us, we will be happy to assist you. To date, we have been able to help every customer.
ATTENTION! The application of the described measure may interrupt correct functionality, in the case of a failure causing one of the
indicator lights to increase in fl ash frequency in order to alert the driver of such a failure. Before each usage of the vehicle, check the
functionality of the indicator lights.
ATTENTION!
These resistors will heat up if the indicator is used for an extended period. Make sure that other components are safe.
The Kellermann micro 1000 LED / LED white / Dark / Extreme system is equipped with the tried-and-trusted
Long Life Protection Guard®
circuit, which ensures extremely long life with LED technology. It is not necessary to replace the illuminant and, due to the laws for device
approval, it is not allowed.
ELECTRICAL CONNECTION
Installation Manual micro 1000 LED / LED white / Dark / Extreme
Dear customer,
thank you for placing your trust in us by purchasing this product. Please read these instructions carefully and completely before
deciding whether you would like to do the installation yourself or have it done by a specialist. If you have any questions or concerns,
or if you require replacement parts, please send us an e-mail (
) or call us (+49 (0)241/9 38 08-0). We are
happy to assist you.
NOTE:
micro 1000
All Kellermann micro 1000 LED / LED white / Dark / Extreme are ECE-approved for motorcycles as documented by the licence number stamped
onto the lens. This means that you may use two micro 1000 LED / LED white / Dark / Extreme units, in accordance with installation
specifi cations, instead of the original indicator lights without any additional entries in your vehicle documents or presentation to a vehicle
inspection organization in Germany, or equivalent in other EU member states.
You do not need to carry any special documentation. This
applies to all motorbikes licensed under EU law and the corresponding lights.
ATTENTION!
The warranty will not apply if your micro 1000 LED / LED white / Dark / Extreme system has not been correctly installed or
connected to the electrical supply on your motorcycle. Do not carry out the installation unless you are qualifi ed to do so; otherwise, leave the
installation and connection work for your micro 1000 LED / LED white / Dark / Extreme to a qualifi ed repair shop. The warranty does not apply
to damage due to wrong connection or excess voltage (such as due to a defective alternator regulator).
ATTENTION!
Improper mechanical installation or orientation of your micro 1000 LED / LED white / Dark / Extreme lights may invalidate your
motorcycle’s roadworthiness and insurance protection, or even lead to accidents. Before every usage of your vehicle, check whether the
indicators are correctly mounted and fully functional.
ATTENTION!
Your micro 1000 LED / LED white / Dark / Extreme lights may heat up during use. Contact with bare skin or heat-sensitive objects
may lead to damage or injury.
ATTENTION!
Each micro 1000 LED / LED white / Dark / Extreme is fi tted with a vibration-absorbing, elastic fastening arm (silent rubber
adapter). This wearing part is designed to protect your micro 1000 LED / LED white / Dark / Extreme from damage at slight defl ections of up to
15°. The adaptor will break on larger defl ections, such as from a crash or vandalism, to prevent breakage to your valuable indicator; the rubber
will overstretch and tear, or the inside will sustain so much damage that it may fail at a later time. In this case, you may order a new silent rubber
adapter as a spare part at two thread fastening lengths – Order No. 123.610 (40 mm thread length) or 123.620 (20 mm thread length) from a
retail specialist or directly from
www.kellermann-online.com
.
INSTALLATION
ATTENTION!
Make sure that your motorcycle is standing fi rmly before you start work, as a fall may lead to damage to the motorcycle or injury
to you or others.
Dismantle the original indicators. Mount the micro 1000 LED / LED white / Dark / Extreme in place of the original indicators, or drill an 8.5 mm
diameter hole and fasten the micro 1000 LED / LED white / Dark / Extreme at
8 Nm
with the self-locking M8 nut supplied. Make sure that the
surface under your micro 1000 LED / LED white / Dark / Extreme where the wires will emerge is protected from splash water. Mount the micro
1000 LED / LED white / Dark / Extreme in such a way that the beams run horizontally in your bike’s direction of travel. Alignment is important to
safety in traffi c and essential to your bike’s roadworthiness, as a bike with incorrectly aligned lights is easy to overlook on the road.
Make sure that you keep the following gaps in selecting your fastening point:
www.kellermann-online.com
micro 1000
LED
micro 1000
LED White
micro 1000
Dark
micro 1000
Extreme
Front
A
Rear
C
mounting
surface
mounting
surface
B
Edge of
the illuminating
surface of the
headlamp
mounting
surface
C
A
B
C
C
A
B
C
C
A
B
C
C
A
B
C
D
min. 20 mm
min. 109 mm
min. 0 mm
min. 169 mm
min. 109 mm
min. 35 mm
min. 169 mm
min. 95 mm
min. 28 mm
min. 155 mm
min. 95 mm
min. 28 mm
min. 155 mm
micro 1000 LED
micro 1000 LED white
micro 1000 Dark
micro 1000 Extreme
D
Page 1
english
Page 2
english
Refer to the 93/92/EWG guideline available at www.eur-lex.europa.eu for further mounting regulations.
