Keller LD350 Operating Instructions Manual Download Page 16

09

Operating instructions

smart slider - Operating instructions

09. Legal notice

All information contained in this manual has been compiled to the best of our knowledge and tested 

with care. Nevertheless, errors cannot be completely ruled out. For this reason, the information contained 
in these instructions is not associated with any obligation or guarantee of any kind. As a result, Keller 
Minimal Windows S.A. accepts no responsibility and will not accept any consequential or other liability 
arising in any way from the use of this information - or any part thereof - including for any infringement 
of patent rights which may result.

Likewise, Keller Minimal Windows S.A. does not guarantee that the processes described are free 

from the property rights of third parties. The reproduction of common names, trade names, product 
descriptions, etc. in this work does not justify the assumption that such names are to be considered 
free in the sense of trademark and brand protection legislation and may therefore be used by anyone, 
even without special labelling.

The contents and data contained in this work are protected by copyright. All rights to the contents are 

the sole property of Keller Minimal Windows S.A..

Any transfer to third parties and any further use or exploitation of the contents outside the legal limits 

- in particular those of the copyright law - is not permitted without the prior written consent of Keller 
Minimal Windows S.A..

Luxembourg law applies.

Copyright © 2021 Keller Minimal Windows S.A.

Responsible publisher

Keller Minimal Windows S.A.

38-40, Route de Wilwerdange
L-9911 Troisvierges
Tel. +352 28 38 66 01
[email protected]
www.minimal-windows.com

16

Keller minimal windows

®

997-00220 

| 05-2022

Keller minimal windows

®

Summary of Contents for LD350


















Reviews: