background image

 Series 3700 Cable & Connector Instructions 

 
 

Model 3792-KIT104-R 

The Model 3792-KIT104-R kit is a 104-pin solder-cup connector kit terminated with a male D-sub connector. 

Figure 13: 104-pin male D-sub connector kit assembled

 

 

WARNING 

Make sure the instrument that you are installing is in a powered-down state 
with all cables unplugged. Failure to install an instrument in a discharged 
state may cause personal injury or death from electrical shock. Do not 
exceed the maximum specifications of the switching module. 

 
 

To prevent electrical shock, observe the following safety precautions: 

 

• 

Both ends of the cable must be connected before applying any power 

 

to the system. 

• 

Remove all power in the system before connecting the cable to a 

 

switching module or external circuitry. 

• 

Both D-sub connector shells of this cable must be connected to a 

 

safety earth ground. A shock hazard exists when voltage levels greater  

 

 

than 30V RMS, 42.4V peak, or 60V DC are present. 

Maximum signal level 

The Model 3792-KIT104-R connector kit is rated for 300V RMS. 

Maximum current rating 

The Model 3792-KIT104-R connector kit maximum current is 5.0A. 

Pin number identification 

Pin number identification for the Model 3792-KIT104-R D-sub connector is shown Figure 14 below: 

Figure 14: Model 3792-KIT104-R kit pin number identification 

Male D-sub connector: 

1

64

85

22

43

21

84

104

42

63

 

Contacts 

The contact is 22 AWG maximum, and an insertion tool (not included) is required (part number 3791-CIT). 

         

                                                        

PA-949 Rev. D / May 2011 

13 

Summary of Contents for 3700 series















Reviews: