background image

 

Page 7 

 

 

DOC0935 (26 July 2022 12:02) 

www.keit.co.uk 

Back to Table of Contents 

 

 

Figure 3: Purge inlet and outlet locations on ASM0627-10-Z-Cx-Ex-Gx-D3x 

The ideal purge gas is dry nitrogen. Alternatively, dry air from a purge gas generator can be 
used. The output from this purge gas generator should have a minimum quality according to 
ISO8573-1:2010  of  Class  1:2:1  (dust:water:oil)  or  better.  Keit  can  recommend  suitable 
generators  that  achieve  this  outlet  air  quality;  contact  [email protected].  Purge  gas 
generators may include an internal compressor or use factory-supplied compressed air with a 
minimum quality of Class 4:4:4 (dust:water:oil). 

 

NOTE

 

All  FTIR  spectrometers  are  very  sensitive  to  water  vapour  and 
carbon  dioxide.  Even  in  well-controlled  environments,  e.g., 
laboratories,  environmental  changes  can  be  large  enough  to 
cause  significant  changes  in  the  spectrum.  We  STRONGLY 
recommend purging the instrument at all times. 

 

To purge the instrument:

 

 

  Remove the blanking plug from the gas purge inlet on the instrument; this is a push fit 

connector.

 

  Connect a 4mm diameter gas hose to the purge inlet port.

 

  Ensure the gas tube is connected to a suitable gas supply via a flow meter.

 

  Adjust the total flow to 0.5 - 2 litres per minute (The pressure drop through the unit is 

<1 barg).

 

  Do  not  turn  off  the  purge  during  normal  operation;  this  will  impact  the  instrument

’s 

performance.

 

  If  the  purge  tubing  is  disconnected,  the  blanking  plug  must  be  fitted  to  the  inlet 

connection on the probe to maintain the IP rating and exclude dust. 

 

The  IRmadillo  requires  a  stabilisation  period  of  >12  hours  once  powered  on  and  purging 
started. This is to allow the internal components to reach a stable temperature and complete 
purging.  Once  fully  purged  the  instrument  is  very  robust  against  changes  in  ambient 
conditions, provided the purge gas supply is maintained. 

2.3.  How to connect data communications 

Like the power cable, the IRmadillo is supplied with dual flying leads for communication that 
are  permanently  connected  through  cable  glands.  You  must  ensure  that  the  cables  are 

Summary of Contents for IRmadillo










































Reviews: