background image

TECHNICAL DATA AND SAFETY 

 

 

 

 

 

 

 

 

Page 9 

In order to maintain continued flushing pump efficiency and reliability it is of 
paramount importance that all equipment is thoroughly washed with clean water 
after every use. 
 
12 Months parts and labour warranty subject to fair wear and tear and no misuse. 
 
The manufacturer and distributor reserve the right, that in the event of a fault claim 
they will repair or replace accordingly at their discretion. 
 
NOTE: - These notes are for guidance only and in no way will any claims for any 
damages be entered into in any way whatsoever, however caused. 
 
 

SAFETY TIPS 
 

As with all large or heavy goods, care should be taken to prevent injury. 
Always follow safety guidelines laid out in the chemical manufactures instructions.  
It is recommended that a RCD (residual circuit device) is used.                               
Regular inspection of power lead and plug is strongly recommended. 

 

Dimensions: W43 x D48 x H56 (cm)                                       
Weight: 18 KG with transport trolley                             
Tank capacity: 37 litres                                       
Compatible with all approved chemicals                 
Working fluid temperature up to 70ºC                     
Efficient cleaning up to 20 radiators                                                    
Flow rate: 5,400 ltrs/hr max 

                                                                 

0.45 HP motor with IP54 protection                              
Max working head: 2bar 

 

 

Summary of Contents for Anton Flowclean Plus













Reviews: