VII. FREQUENTLY ASKED QUESTIONS (FAQ)
VIII. TECHNICAL PARAMETERS
b. Settings - User controled output
The command systax:
4321 OUT1 USER
Output 1 activation
4321 OUT1 ON
Output 2 deactivatioan 4321 OUT1 OFF
This allows you to switch the relay in GPS locator and thus remotely enable
or disable a device in a vehicle (such as a siren, lights, radio).
Output 1 activation for a limited time
4321 OUT1 11m
output is active 11 minutes
4321 OUT1 6s
output is active 6 seconds
2.4 Output 2 setings by SMS
4321 OUT2 30
Output will be switched
by impulses 30 seconds
(utilization for horn)
4321 OUT2 60
Output will be switched
permanently for 60 seconds
Default value 60 seconds
It is possible to set those 2 values only (30 or 60)
2.5 GPS locator switching to SLEEP mode
The command systax:
4321 SLEEP
In Sleep mode the protection is turned OFF,
GPS and GSM reciever is turned OFF too.
Sleep mode is automatically deactivated by
switching the ignition ON, or by the signal on
Input 2, or if the car is tilted.
Then the Alarm SMS is sent out.
2.6 GPS locator deactivation
In the GPS OFF mode, the protection is turned OFF, current consuption is
reduced. GPS reciever is turned OFF, GSM stays turned ON.
GPS Sniper deactivation:
4321 GPS OFF
GPS Sniper activation:
4321 GPS ON
Note:
In the case of current shutdown of
„Monitor“ protection and „GPS“ protection (GPS OFF),
the system automatically turns off also the GPS receiver and therefore the „SPEED“
protection can not be used too.
2.7 Zaslanie informačnej SMS z GPS lokalizátora
It is possible to send out any text SMS from the device phone number,
using authorized phone number:
4321 +xxxxxxxxxxxx zzzzzzzzzz
+xxxxxxxxxxxx
- phone number
zzzzzzzzzz
- message text
Note:
The SMS messages recieved by GPS Sniper from other than authorized phone num-
bers are automatically forwarded to authorized numbers (info about the credit status
for example).
Warning:
Do not enter GPS Sniper SIM card phone number as an authorized phone
number! the system may get cycled and huge unexpected fees may occur from GSM
operator, because of the high amount of SMS messages sent!
VI. MOBILE APPLICATION
GPS Sniper device allows you to use a mobile application GPS Sniper for
the smart phones. The application allows you to perform complete system setup and
control the GPS Sniper the similar way, like by the SMS commands. User manual for the
mobile application is part of the application itself. Conact your GPS Sniper producer
about the issue of the application for Android (Google Play) and iOS (Apple Store).
GPS SNIPER
GPS locator MANUAL 2/2
EN
1. PROTECTION
GPS Sniper possible to use for the protection of the vehicle as an autono-
mous device, or together with the existing alarm. If you are using localizer absolutely,
you could use the “GPS ON” mode and “Monitor” mode. If you use it with the external
car alarm, then you have additionally available “INPUT Alarm” mode.
WAYS OF PROTECTION:
- 1.1
Motion detected by GPS unit
- 1.2
Turning the ignition ON in “Monitor” protection
- 1.3
Input 2 control– if it is enabled
- 1.4
JAMM protection (detection of GSM signal jamming) – if it is enabled
- 1.5
Car battery discharge protection
- 1.6
Speeding– if it is set
- 1.7
Tilt sensor protection – if it is enabled
1.1 „GPS ON“ Mode
GPS triggers alarm, if the vehicle is set in motion and the ignition is turned
OFF. It is the protection against towing the car. This type of protection is recommended
to have turned ON permanently. It is not necessary to deactivate before driving. If you
start the car, GPS protection is interrupted automatically by itself throughout the drive.
Activating the function by SMS command „4321 GPS ON“.
Activation:
GPS protection is activated and deactivated by ignition, it is deactivated by
starting the car, activated with the ignition turned OFF. GPS alarm is trigerred when the
vehicle is set to move and the ignition is turned OFF (pulling off).
Response to GPS alarm:
During the active period of GPS alarm (alarm
triggered) the alarm SMS are sent also with
the GPS location. The total number of SMS sent
depends on the actual configuration set.
You can cancell the GPS alarm, if you send
SMS command: „4321 GPS OFF“.
1.2 „MONITOR“ Mode
The mode is identical to the GPS ON mode, but does not consider the actu-
al ignition status. GPS alarm is triggered allways, if the car is set into move, no matter if
ignition ON or OFF.
Activation:
It is activated by dialing GPS Sniper telephone number from an authorized
phone number (GPS Sniper rings 2x then reject the call).
Deactivation:
It is deactivated by dialing the GPS Sniper phone number from an authori-
zed phone number (deactivation is confirmed by rejecting the call from the GPS Sniper
side). The deactivation must be carried out before each drive. (the call is rejected from
the GPS Sniper side immediately).
GPS alarm triggering:
GPS alarm is triggered whenever the car is set to move (if the mode active).
Response to GPS alarm:
The device will send the alarm SMS immediately in the form „ALARM, IGNI-
TION IS ON“, if the ignition is ON by the „Monitor“ mode active. The alarm SMS also
includes GPS coordinates and a link to „maps.google.com“. The alarm SMS are sent re-
peatedly with the GPS location information throughout the period of GPS alarm is acti-
ve. Total number of alarm SMS sent depends on actual configuration set. You can can-
cell the GPS alarm by dialling the GPS Sniper phone number from any of the authori-
zed phone numbers. The cancellation is confirmed by immediate rejection of the call.
1.3 Input 2 control protection
You could utilize the Input protection, only if there is oem or aftermarket
alarm already installed in the car. The output of the original alarm is connected then to
input contact of GPS Sniper. The device will send SMS message to authorized phone
number, if the signal occurs on the input of GPS Sniper.
Note:
Let the connection to be performed by a proffesional service.
Activation:
The command systax:
4321 INPUT ON 0.2 to turn ON
(alarm input must be in ON-state at least 0,2 seconds)
4321 INPUT ON 1.5 to turn ON
(alarm input must be in ON-state at least1,5 seconds)
Deactivation:
INPUT protection could be deactivated by SMS command
The command systax:
4321 INPUT OFF
to turn OFF -
set as OFF by default
Alarm triggered:
Alarm Input 2 is active only if the ignition is OFF. After the alarm is trigered,
the Input 2 is deactivated for 2 minutes.
1.4 Detection of GSM signal jamming
The command systax:
4321 JAMM ON
to turn ON
4321 JAMM OFF
to turn OFF
set as turned OFF by default.
We recommend the fuction to be active with
connection to car alarm, siren or the horn, because the user will recieve the SMS infor-
mation about the signal jamming only after the GSM signal recovery.
1.5 Car battery discharge protection
The command systax:
4321 BATTERY xx
xx- minimum voltage value
Default value 11,5V
- alarm SMS is sent out, if the actual battery
voltage drops below the set value for at least
2 minutes.
1.6 Speeding protection
The command systax:
4321 SPEED xx
xx- value in km/h 0-200,
- if the value set as 0 (zero),
alarm SMS will not be sent at all
Default value 130 km/h.
Alarm SMS is send out automatically, if the car speed exceeds the set value.
1.7 Tilt sensor protection
The command systax:
4321 TILT xx
xx value in degrees 0
°
- 30
°
- if the value set as 0
°
(zero),
alarm SMS will not be sent at all
Default value 5°.
The protection is activated automatically, 2 minutes after the ignition is switched OFF.
If the allarm is trigered by tilt sensor, the next alarm possible to trigger only after 2 mi-
nutes had passed.
2. OTHER SETTINGS
2.1 GSM / GPS signal strenght
The command systax:
4321 SIGNAL
Answer:
GSM 96%
GPS 9 SATELLITES
2.2 Alarm notification by dialing authorized phone number
GPS Sniper will dial all the authorized phone numbers and only then will
send alarm SMS, if allarm triggered.
The command systax:
4321 RING ON
- to turn ON
4321 RING OFF
- to turn OFF
2.3 Output 1 setup
a. Settings - to obtain information on the locator status (arm/disarm)
The command systax:
4321 OUT1 ARM
Default setting:
OUT1 ARM
The output is active if “Monitor” protection active.
If the “Monitor” mode deactivated, the output is
deactivated too.
PROBLEM
SOLUTION / THINGS TO CHECK OUT
The device will not
turn ON
• Check out the power supply connection wires and input
ACC wire
The device will not
recieve the GSM
signal
• Check the SIM card correct insertion
• Check the GSM signal coverage with the operator
•Check if the PIN code protection of the SD card is turned
OFF
•Yellow LED must be ON, if GSM signal recieves OK
The device not
response to SMS
command
•
Check, if the device is turned ON and if recieves the
GSM signal. You can check it by dialing the GPS Sniper
phone number
• Be sure, SMS command entered in correct form with va
-
lid PIN code. If you use a prepaid SIM card, make sure the
SIM card is still active and there is enough credit for sen-
ding SMS.
• Before the first SMS command sent, wait approximately
2 minutes after the device is turned ON, the system initiali-
zation must be performed first. If you want to send another
SMS command, wait pls until the previous SMS command
is processed.
The device response
to SMS commands,
but does not response
to dialing from autho-
rized phone number
• Check the validity of the authorized phone number, inclu
-
ding international phone prefix by the SMS command
CONFIG TEL.
• Check, if there is the CLIP (Caller ID) service activated
with the SIM
The device will not
trigger GPS alarm
• Check, if there is GPS protection mode activated
(GPS / MONITOR).
• Check the correct connection and location of GPS aerial.
• Check the authorized phone numbers, if it is correct
False GPS alarm
triggered
• Check, if the GPS aerial is installed horizontally and is not
shielded by metal parts from above.
• The device has sophisticated algorithm for the alarms trig
-
gering. Nevertheless, a false allarm may be triggered in
some specific cases, anyway it is not a failure of the devi-
ce or the incorrect installation. This can happen in a garage
near the high buildings, where the device could recieve re-
flected GPS signal for longer period of time.
GPS Sniper PIN code
forgotten
• Please contact your dealer, the device may be restored
to factory settings, including PIN only by the manufacturer
4321 JAMM ON
4321 GPS OFF
4321 BATTERY 11.5
4321 SIGNAL
POSITION CHANGE
DETECTED TSS 16
http://www.maps.
google.com/
maps?q=48.970596,
18.189840
4321 RING ON
4321 SLEEP
4321 OUT1 ARM
Operating temperature from -20°C to +80°C
ECU measures
90 x 54 x 12,8 cm
ECU weight
app. 50g
Power supply
9V to 36V
Current consuption
by GPS protection: 40 mA
Current consuption
by SLEEP mode: 17 mA
Output 1
300 mA
Output 2
300 mA
Battery
built-in Li-On, 300 mAh
4321 SPEED 120
4321 TILT 20
4321 OUT1 USER
4321 OUT1 11M
4321 OUT2 30
