Keeler Tonocare Manual Download Page 29 | Manualshive

Page: 29 / 40

background image

29

Follow the instructions from this section for the safe

care, cleaning and maintenance of your TonoCare.

4.1 General product care

Always inspect the product before use, checking for normal
start-up.

Do not attempt to perform product disassembly, reassembly or
repair. These should only be done by personnel trained and
qualified by Keeler, following the instructions in the service
manual.

Do not store the product in a dusty environment, as the dust
may enter the puff system, and be dispelled to the patient’s eye
during use.

Regular inspection

Inspect your power supply unit and cable for damage regularly.

Before inspecting, disconnect the power supply from the
TonoCare and the mains supply.

If the outer insulation of the cable appears to be damaged
discontinue use immediately. Contact your local dealer for a
replacement.

4.0 Product care and maintenance

«
...
27
28
29
30
31
...
»

Summary of Contents for Tonocare









































Reviews:

No comments

Related manuals for Tonocare

Brand: Pall Pages: 51

Brand: ZAMST Pages: 21

Brand: Salvis Pages: 40

Brand: IDEAL Pages: 2

Brand: NARGESA Pages: 50

Brand: FEAS Pages: 72

Brand: idi Pages: 20

Brand: G&G Pages: 2

Brand: H&S Pages: 46

Brand: WalkMed Pages: 2

Brand: Walinga Pages: 20

Brand: Wassermann Pages: 24

Brand: A.J.Antunes Pages: 24

Brand: B&G Pages: 2

Brand: M-system Pages: 4

Brand: PI Pages: 65

Brand: Tieline Pages: 359

LUNAQUA Classic LED

Brand: Oase Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands