KEB COMBIVERT S6 Series Instructions For Use Manual Download

Page: 52 / 66

brAKe cONTrOL AND TeMPerATUre DeTecTION

• Deactivate the evaluation (pn33 =7)
or
• Install bridge between terminal X1C.5 and X1C.6 (dr33=1)

4.3.4 connection of a KTy sensor

NOTICE

No protection of the motor winding in case of wrong connection.

►

Operate KTY sensors in forward direction. Non-observance leads

incorrect measurement in the upper temperature range.

►

KTY sensors may not be combined with other detections.

Name

TA1 (X1C.5); TA2 (X1C.6)

function

Temperature sensor input

Stetting

dr33=0; KTY84/130

dr33=3; KTY83/110

Table 27:

Connection of a KTY sensor

TA1

TA2

KTY84

①

Legend

Connection via shield plate (if not available, place on the mounting plate).

Figure 22:

Connection of a KTY sensor

Summary of Contents for COMBIVERT S6 Series



































































Search results

Summary of Contents for COMBIVERT S6 Series

Reviews:

Related manuals for COMBIVERT S6 Series

Brands by name

Popular brands

KEB COMBIVERT S6 Series, Instructions For Use Manual

Search results

Summary of Contents for COMBIVERT S6 Series

Reviews:

Related manuals for COMBIVERT S6 Series

Brands by name

Popular brands