background image

3

NOTE:

Because of the superior heating characteristics

and heat retention properties found in the Teppanyaki
Griddle, operating temperatures should be set 10°F to
25°F (6°C to 14°C) below conventional griddles.

2.  Set the thermostat to the desired temperature and

wait ten minutes for preheating.

3.

See figure 3-1 for proper food placement. The
thermostat sensing bulbs are located below the
plate.

4.

Load the product to the left and right of each
sensing bulb, then fill the area above the
thermostat sensing bulb. See figure 3-1.

Figure 3-1
Sample configuration of proper food placement

If you cook over the sensing bulb only, you are drawing
heat from that section, activating the thermostat to call
for more heat even though the area around it is still at
the temperature setting. This will result in higher
surface temperatures which will affect your cooking
and product appearance.

Figure 3-2
Top view placement of elements under Teppanyaki Griddle
plate.

4.  After each load, scrape the griddle surface

completely clean using the 4" (102mm) wide
replaceable blade scraper.

DO NOT HACK, CHOP, HIT OR CUT ON THE
TEPPANYAKI SURFACE. You will dent the steel plate
under the trivalent chrome. It is even possible to hack two
nicks close together and actually tear the Teppanyaki
surface as the chromium will not stretch. Below is a sketch
showing the side view of a griddle plate and how the
surface can be damaged.

Figure 3-3
Surface Damage

Never use griddle scraper on the polished steel
Teppanyaki Griddle. This will damage the surface.

Damage done to the Teppanyaki surface is irreparable.

CLEANING THE MIRACLEAN

®

GRIDDLE

The surface of the Teppanyaki Griddle is very durable
and with proper care, following the procedures below,
will last many years.

A sample of Keating Klenzer and a 4" (102mm) scraper
are included with each new Miraclean

®

griddle.

1.

Scrape Teppanyaki surface with the Keating
scraper.     

2.

Clean with potable tap water and a palmetto brush.

.

CAUTION

CAUTION

Load #1

Load #3

Load #2

Thermostat Bulb Location

HEATING 

SECTION

Summary of Contents for MIRACLEAN












Reviews: