background image

2

II INSTALLATION

This UNIT must be installed, inspected, calibrated and

serviced by qualified and/or certified and licensed

service personnel - you may void your Keating

warranty if installation is not completed per local,

national and Keating specifications. Contact your

dealer for assistance.

INSTALLATION

Installation must conform with local codes or, in

absence of local codes, with the current National

Electrical Code ANSI/NFPA 70 or Canadian Electrical

Code CAN22.2 as applicable.

DAMAGE DURING

SHIPMENT

The griddle has been assembled, tested and inspected

at the factory. Upon arrival, the complete griddle should

be checked for any damage that may have occurred

during shipment.
The carrier is responsible for all damage in transit

whether visible or concealed. Do not pay the freight bill

until the griddle has been thoroughly checked for

damage. If concealed damage is found later, contact

the carrier immediately to file a claim.

What to do if equipment arrives damaged:

VISIBLE LOSS OR DAMAGE -- Be certain to note this

on the freight or express receipt and have it signed by

the delivery person.
FILE CLAIM FOR DAMAGES IMMEDIATELY --

Regardless of extent of damage.
CONCEALED LOSS OR DAMAGE -- If damage is

noticed when equipment is unpacked, notify the freight

company immediately, and file a “concealed damage

claim”. This MUST be done immediately. Be sure to

retain the shipping container for inspection.
Keating does not assume responsibility for Loss or

Damage incurred in transit.

POSITIONING

The griddle must be placed under an exhaust hood

with a fire retardant system. Your ventilation hood,

when installed, must conform to the current

ANSI/NFPA 96 standard. ALL connections and

placement must comply with local and national codes.

It is the responsibility of the owner and local installer to

comply with these regulations when installing the

griddle. 

NOTE: NOT FOR OUTDOOR INSTALLATION

LEVELING

Your MIRACLEAN® Griddle will operate at its highest

efficiency when properly leveled. Place a level on the

griddle plate from side to side. For griddles on legs, the

bottom foot of the leg is adjustable. Turn

counterclockwise to decrease height or clockwise to

increase height until level. For griddles on stands with

casters, the casters are adjustable by loosening the

jam nut and turning the caster in or out. When the

desired level is reached, tighten the jam nut.

Adjustments of more than 3/4” are not recommended

on any caster. The same procedure should be followed

to the level the griddle from front to back.

Figure 2-1
Leveling Griddle

RESTRAINING

On griddle installations on stands with casters, casters

and jam nuts must be completely tightened. Adequate

means must also be provided to limit the movement of

the appliance.
The restraint must be attached to the rear of the griddle

as close as possible to the center line width and the

bottom of the cabinet back to allow the restraining bolt

to be anchored to the cabinet back between the cabinet

bottom and inner liner to ensure positive support to

restrain griddle movement.

IF DISCONNECTION OF THE

RESTRAINT IS NECESSARY, IT

MUST BE RECONNECTED WHEN

THE MIRACLEAN® GRIDDLE IS

RETURNED TO ITS ORIGINALLY

INSTALLED POSITION.

Summary of Contents for MIRACLEAN






















Reviews: