background image

6

1

Check the Ceiling Fan condition annually. If a 

problem occurs, stop using the Ceiling Fan. Then 

refer to authorized dealer.

 

Check point:

Loosened screws, safety wire condition, motor shaft 

damage, etc.

2

Ensure the Safety Switch is in good condition.

If a problem occurs, stop using the Ceiling Fan. 

Then refer to authorized dealer.

3

Keep the Ceiling Fan clean. Wipe away dirt with 

a clean soft cloth, ordinary soap and water. Wipe 

it again to dry it. Do not use solvents (gasoline, 

petroleum, thinner, benzine, alcohol, cleaning 

powder, alkaline detergent) or any other chemicals.

• Do not bend the Blade while cleaning.

4

Do not paint the Blades. If damaged, order a new set 

of Blades (3 pieces) from an authorized dealer.

5

When referring to an authorized dealer, show these 

instructions to them and maintain correctly.

6

If the product is broken or damaged, remove it from 

the ceiling and replace with new. This is to avoid the 

Ceiling Fan drops.

7

The Ceiling Fan suspension system should be 

examined at least once every two years.

8

Do not modify or repair the LED light. If a problem 

occurs, refer to authorized dealer (for E48GP).

Safety Switch / 

ԊӒ໠ᜰ

Switch Lever / 

໠ᜰ؋

Wrong Position /

ᒿᇲ՝ည

Correct Position /

ғጂ՝ည

Maintenance

ᆰও

1

፜ؐԑۡਢᔮࢥӤਉޟޑݷȄԃݎю౪୰ᚠȂ፜ୄХٺ
ҢԤᜰӤਉȄġณࡣ፴ၚ݈୛ܖ௲᠌င᎛୦Ȅ

 

ᔮࢥᘈ

:

ᖳ๛ᚬಳȂ߳ᓎጣޑݷȂีଢ଼ᐠᙽଢ଼໅ཬᚽ้้Ȅ

2

ጂ߳ԊӒ໠ᜰġ೎ܻيԁޑᄘȄ
ԃݎю౪୰ᚠȂ፜ୄХٺҢԤᜰӤਉȄ
ณࡣ፴ၚ݈୛ܖ௲᠌င᎛୦Ȅ

3

߳ࡻӤਉ఼ዓȄҢୁ౑ޟ೺Ҁȃල೽޳غڷЫܡўԴ
ၬȄӔܡΙԩ஠ϞܡୁȄϸϼٺҢྙᏘȞءݶȂݶȂใ
ភᏘȂॄȂନᆠȂўԴ઱ڷᢃܒࢿᅥᏘȟܖӈդڏтϽ
ᏰސࠢȄ

ġ

˙

఼ࢿਉᖎਢ፜ϸϼ׷᠉ਉᖎȄ

4

ϸϼ࣏ਉᖎ༯ᅘȄषਉᖎཬᚽΟȂ፜௲୦ॏᗊཱིޟਉᖎġ

(3

ġݛ

)

Ȅ

5

࿋ௌ፴ၚ௲᠌င᎛୦ਢȂ፜өтঈюҰԪࡾҰਪо߯т
ঈғጂӴ໌՗ᆰওȄ

6

ष౰ࠢϐ׷ᘞܖཬᚽȂ፜௃Ј߆ݖΰܶଶӤਉȂณࡣ඲
ΰཱིޟӤਉȄ೻࢐࣏Ο٩ХӤਉ௬ဣȄ

7

࡚ដؐڍԑՍЍᔮࢥӤਉ᝚௮فಛΙԩȄ

8

፜ϼ׽၆ܖও౩၎ġ

LED

ġᐷȄԃݎีҡޑݷȂ፜ᖒ๜௲᠌

င᎛୦

 (

ᎌҢܻ

 E48GP).

Summary of Contents for E48HP





















Reviews: