■
Copyrights
●
You are not allowed to copy, distribute, publish, modify or edit the data you downloaded using this product without the
consent of the copyright holder, except for personal use, under the copyright law.
In addition, do not use or modify portraits or names of other individuals without their consent, as it might infringe on rights of
portrait.
■
Backup content on the product
●
Please back up important content downloaded for the product. Content recorded to memory on the product sometimes
disappears or is altered by unexpected factors, such as static electricity or a fault, repair, mishandling, etc.
* How to make backups: you can back up setting contents of the product in your PC. Please refer to “
取扱説明書 詳細
版
(Full Instruction Manual)” (Japanese). Note, however, that there are some data that cannot be copied by using these
means. Please be forewarned.
PIN code
■
PIN code
●
To prevent unauthorized use of the au Micro IC Card (LTE) by a third party, you can set the product to require PIN code entry
every time connecting to a PC. You also need to enter PIN code when setting whether the PIN code entry is required.
●
If the PIN code is incorrectly entered three times consecutively, the PIN code will be locked. You can unlock the PIN code
using PUK code.
* PIN code is “1234” and PIN code entry was set to not be required at the time of purchase. You can change PIN code to
any four- to eight-digit number, and set the PIN code entry to be required as necessary.
* PIN code cannot be reset by initializing the product.
■
PUK code
●
In case the PIN code is locked, you can unlock it by entering the PUK code.
* PUK code is an eight-digit number given at the time of purchase, which is printed on the back side of the plastic card on
which your au Micro IC Card (LTE) is attached.
*After entering the PUK code, you need to set a new PIN code in “PIN management”.
* If the PUK code is incorrectly entered ten times consecutively, contact an au shop, PiPit or Customer Service Center.
Notes on the supplied software
Pay attention to the following points when using the software supplied with the product
●
The software is licensed to you for use only. Copyright of the software is not transferred to you. You may not transfer or sell
the software to any third parties.
●
You may copy the software for backup purpose only. You may not copy the software for the purpose of transferring or
selling to others.
●
The Company is not liable for any loss arising by using the software or claim for damages against you from the third party.
After-sales service
■
When asking for repair
For repair, contact Keitai Guarantee Service Center.
During the warranty period
Repairs will be done based on the terms of services of the free-of-charge repair warranty
described on the warranty card.
Outside the warranty period
We shall repair the product for a charge as requested by the customer if repair renders it
usable.
•
Before handing in the product for repair, make a backup of the contents of memory since they may disappear during repair.
Note that the Company shall not be liable for any damages and loss of income should the contents of memory be altered or lost.
•
Recycled parts that meet the Company's quality standards are sometimes used for repair.
•
Collected au products by Replacement product delivery service which you used before are recycled to products for
replacement after repairs. Also replaced parts by au after-sales service are collected and recycled by KDDI. They are not
returned to customers.
■
Performance parts for repair
The Company retains performance parts for repair of Speed USB STICK U01 main unit and its peripherals for four years after
discontinuation of production.
“Performance parts for repair” refers to parts required for maintaining the functions of the product.
■
Warranty card
At the store of purchase, thoroughly check and read the name of the retailer, date of purchase and other necessary details
filled in on the warranty card, and be sure to keep it in a safe place.
■
Keitai Guarantee Service Plus LTE
An after-sales service membership program on a monthly basis called “Keitai Guarantee Service Plus LTE” (monthly fee: 380 yen
excluding tax) is available for using your au product for a long time without worries. This service expands coverage for many troubles
including malfunction, theft and loss. For details of this service, refer to au homepage or contact Keitai Guarantee Service Center.
•
You can apply for membership only at the time of purchasing your au product.
•
Once you cancel the membership, you cannot reapply for it until you purchase an au product next time.
•
Note that when changing the model or purchasing an extra au product, this service only covers the most recently purchased
au product.
•
When an au product is handed over to you or someone else, the Keitai Guarantee Service Plus LTE membership is also
handed over to the successor of the product.
•
When you get a new au product by changing the model or purchasing an extra product, the “Keitai Guarantee Service Plus” /
“Keitai Guarantee Service Plus LTE” membership for the old au product is automatically canceled.
•
Service contents are subject to change without notice.
■
au Micro IC Card (LTE)
The au Micro IC Card (LTE) is lent to you by au. In case of loss or damage, the card will be replaced at your expense. When
malfunction is suspected, or in case of theft or loss, contact an au shop or PiPit.
■
After-sales service
If you are unsure about anything regarding after-sales service, contact the following service contact.
Customer Service Center (for service canceling procedure in case of loss, theft or theft)
From a land-line phone,
From fixed-line phones:
0077-7-113
From au cell phones:
113
without area code
For loss, theft or damage
(toll-free)
In case above numbers are not available, call (toll-free)
0120-977-033
(except Okinawa)
0120-977-699
(Okinawa)
Keitai Guarantee Service Center
For loss, theft, damage
(toll-free)
From fixed-line phones/au cell phones,
0120-925-919
Business hours : 9:00-21:00
(7 days a week)
Business hours : 9:00-20:00 (7 days a week)
Business hours : 24 hours (7 days a week)
Customer Service Center
Pressing “zero” will connect you to an operator,
after calling “157” on your au cell phone.
From fixed-line phones:
0077-7-111
From au cell phones:
157
without area code
For general information, charge and
operation information
(toll-free)
0077-7-113
(toll-free)
From an au cell phone,
113
(toll-free)
Business hours: 24 hours (7 days a week)
Keitai Guarantee Service Center (for loss, theft, damage)
From a land-line phone/au cell phone,
From fixed-line phones:
0077-7-113
From au cell phones:
113
without area code
For loss, theft or damage
(toll-free)
In case above numbers are not available, call (toll-free)
0120-977-033
(except Okinawa)
0120-977-699
(Okinawa)
Keitai Guarantee Service Center
For loss, theft, damage
(toll-free)
From fixed-line phones/au cell phones,
0120-925-919
Business hours : 9:00-21:00
(7 days a week)
Business hours : 9:00-20:00 (7 days a week)
Business hours : 24 hours (7 days a week)
Customer Service Center
Pressing “zero” will connect you to an operator,
after calling “157” on your au cell phone.
From fixed-line phones:
0077-7-111
From au cell phones:
157
without area code
For general information, charge and
operation information
(toll-free)
0120-925-919
(toll-free)
Business hours 9:00-21:00 (7 days a week)
Online Repair Desk (24 hours a day over the Internet)
* Available only from PCs or smartphones
https://cs.kddi.com/support/n_login.html
•
The Application for the Internet acceptance, if “damage”, “wet”, “theft” and “loss” are eligible. In the
case of spontaneous failure (not the cause damage, such as water wet, but does not activate or other), it
will be accepted by phone for interview is required.
•
To apply for the Internet, you need the e-mail address.
■
au after-sales service information
Service
Keitai Guarantee Service Plus LTE
Member
Others
Replacement cell phone delivery
service
Spontaneous
failure
1st year
Free of charge
No recompense
2nd year or later
Customer charge
1st : 5,000 yen
2nd : 8,000 yen
Partially damage, water soak,
irreparable damage, theft or loss
Holding over and repair
Spontaneous
failure
1st year
Free of charge
Free of charge
2nd year or later
Free of charge
(for 3 years)
Actual cost
Partially damage
Customer charge
Upper limit: 5,000 yen
Water soak, irreparable damage
Customer charge
10,000 yen
Loss, theft
No recompense
No recompense
(model change)
*Charge amounts are all tax-excluded.
Replacement cell phone delivery service
•
When you have trouble with your au product, replacement product (same model, same color) is delivered by calling to.
Return your damaged product within 14 days after the replacement of the product is delivered.
•
Available up to twice in a year from the day you use this service as a start day. If you do not use this service in the past year
for the subscription to this service, it will be 1st and if you use, it will be the 2nd.
* For details, refer to au homepage.
Holding over and repair
•
Damages and malfunctions intentionally caused by the customer as well as those due to modification (e.g. disassembly,
change of parts, painting, etc.) by the customer are not covered by this service.
•
You cannot receive a refund for the replacement of the outer casing due to stains, scratches, paint removal, etc. on the outer casing.
Specific Absorption Rate (SAR) of Mobile Terminals
This model Speed USB STICK U01 device complies with Japanese technical regulations and international guidelines
regarding exposure to radio waves.
This device was designed in observance of Japanese technical regulations regarding exposure to radio waves(*) and limits to
exposure to radio waves recommended by a set of equivalent international guidelines. This set of international guidelines was
set out by the International Commission on Non-Ionizing Radiation Protection (ICNIRP), which is in collaboration with the World
Health Organization (WHO), and the permissible limits include a substantial safety margin designed to assure the safety of all
persons, regardless of age and health condition.
The technical regulations and international guidelines set out limits for radio waves as the Specific Absorption Rate, or SAR,
which is the value of absorbed energy in any 10 grams of tissue over a 6-minute period. The SAR limit for mobile terminals is
2.0 W/kg. The highest SAR value for this device when tested for intended use described in the instruction manual is 0.669W/kg
(*). There may be slight differences between the SAR levels for each product, but they all satisfy the limit.
The actual SAR of this device while operating can be well below that indicated above. This is due to automatic changes to the
power level of the device to ensure it only uses the minimum required to reach the network. Therefore in general, the closer you
are to a base station, the lower the power output of the device.
During communication, please keep the device farther than 1.5 cm away from your body without including any metals. This
device satisfies the technical regulations and international guidelines.
The World Health Organization has stated that "a large number of studies have been performed over the last two decades to
assess whether mobile phones pose a potential health risk. To date, no adverse health effects have been established as being
caused by mobile phone use."
Please refer to the WHO website if you would like more detailed information.
http://www.who.int/docstore/peh-emf/publications/facts_press/fact_english.htm
Please refer to the websites listed below if you would like more detailed information regarding SAR.
○
Ministry of Internal Affairs and Communications Website:
http://www.tele.soumu.go.jp/e/sys/ele/index.htm
○
Association of Radio Industries and Businesses Website:
http://www.arib-emf.org/index02.html (in Japanese only)
○
HUAWEI TECHNOLOGIES CO., LTD. homepage:
http://consumer.huawei.com/jp/mobile-broadband/support/information/hwd32-jp.htm (in Japanese only)
○
au homepage:
http://www.au.kddi.com/
* Technical regulations are defined by the Ministerial Ordinance Related to Radio Law (Article 14-2 of Radio Equipment Regulations).
Reduction of hazardous substances
This device is compliant with the REACH Regulation [Regulation (EC) No 1907/2006] and RoHS Directive Recast (Directive
2011/65/EU). Batteries (if included) are compliant with the Battery Directive (Directive 2006/66/EC). For up-to-date information
about REACH and RoHS compliance, please visit the web site www.huaweidevice.com/certification.
EU regulatory conformance
■
RF exposure requirements
Important safety information regarding radio frequency (RF) radiation exposure:
RF exposure guidelines require that the device be used at a minimum of 1.5 cm from the human body. Failure to observe this
guideline may result in RF exposure exceeding limits.
■
Certification information (SAR)
This device meets guidelines for exposure to radio waves.
Your device is a low-power radio transmitter and receiver. As recommended by international guidelines, the device is designed
not to exceed the limits for exposure to radio waves. These guidelines were developed by the International Commission on
Non-Ionizing Radiation Protection (ICNIRP), an independent scientific organization, and include safety measures designed to
ensure the safety of all users, regardless of age and health.
The Specific Absorption Rate (SAR) is the unit of measurement for the amount of radio frequency energy absorbed by the
body when using a device. The SAR value is determined at the highest certified power level in laboratory conditions, but the
actual SAR level during operation can be well below the value. This is because the device is designed to use the minimum
power required to reach the network.
The SAR limit adopted by Europe is 2.0 W/kg averaged over 10 grams of tissue, and the highest SAR value for this device
complies with this limit.
■
Statement
Hereby, Huawei Technologies Co., Ltd. declares that this device is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
For the declaration of conformity, visit the web site www.huaweidevice.com/certification.
The following marking is included in the product:
0197
This device may be operated in all member states of the EU.
Observe national and local regulations where the device is used.
This device may be restricted for use, depending on the local network.
FCC Regulatory Compliance
■
RF exposure requirements
Important safety information regarding radio frequency (RF) radiation exposure:
RF exposure guidelines require that the device be used at a minimum of 0.5 cm from the human body. Failure to observe this
guideline may result in RF exposure exceeding limits.
■
Certification information (SAR)
This device is also designed to meet the requirements for exposure to radio waves established by the Federal Communications
Commission (USA).
The SAR limit adopted by the USA is 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported to the FCC
for this device type complies with this limit.
■
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Caution
: Any changes or modifications to this device not expressly approved by Huawei Technologies Co., Ltd. for
compliance could void the user's authority to operate the equipment.
Export Administration Regulations
This product and its accessories may be subject to the Japan Export Administration Regulations (“Foreign Exchange and
Foreign Trade Law” and its related laws). In addition, U.S. Re-export Regulations (Export Administration Regulations) may
apply to this product and its accessories. To export and re-export this product and its accessories, take the required measures
on your responsibility and at your expenses. For details on the procedures, contact the Ministry of Economy, Trade and
Industry or the U.S. Department of Commerce.
Trademarks
Microsoft
®
, Windows
®
, Windows Vista
®
are trademarks or registered trademarks of Microsoft Corporation in the United
States.
The official name for Windows is Microsoft Windows Operating System.
Internet Explorer is a trademark or registered trademark of Microsoft Corporation in the United States/other countries.
Firefox is a trademark or registered trademark of the Mozilla Foundation in the United States/other countries.
Google, Android and Google Chrome are trademarks or registered trademark of Google Inc.
Opera is a trademark or registered trademark of Opera Software ASA. For details about Opera, refer to http://jp.opera.com/.
Mac, Macintosh and Mac OS are trademarks or registered trademarks of Apple Inc. in the United States/other countries.
HUAWEI are registered trademarks or trademarks of HUAWEI TECHNOLOGIES CO., LTD. in China.
Other company names and product names referred to in this manual are trademarks and registered trademarks of
respective companies. ® or TM mark may be omitted in this manual.
For inquiries, call
From fixed-line phones:
0077-7-113
From au cell phones:
113
without area code
For loss, theft or damage
(toll-free)
In case above numbers are not available, call (toll-free)
0120-977-033
(except Okinawa)
0120-977-699
(Okinawa)
Keitai Guarantee Service Center
For loss, theft, damage
(toll-free)
From fixed-line phones/au cell phones,
0120-925-919
Business hours : 9:00-21:00
(7 days a week)
Business hours : 9:00-20:00 (7 days a week)
Business hours : 24 hours (7 days a week)
Customer Service Center
Pressing “zero” will connect you to an operator,
after calling “157” on your au cell phone.
From fixed-line phones:
0077-7-111
From au cell phones:
157
without area code
For general information, charge and
operation information
(toll-free)
December 2014, 1st Edition
KDDI CORPORATION·OKINAWA CELLULAR TELEPHONE COMPANY
Imported by: HUAWEI Technologies Japan K.K.
Manufactured by: HUAWEI TECHNOLOGIES CO., LTD.
