background image

16

Operating Instructions KBL 7900/KBL 7000/KBL Convertible

4.3  Tips for the studio operator 

Daily checks and 

basic settings 

Please make sure  

•  that the tank for the condensed water is checked and 

emptied every day

•  that materials which have been used up are refi lled (8.4) 

and

•  that the settings which can be executed in the service 

levels (see 8.3) of operation, e.g. colour-stimulation, 
aroma, time controls etc. are made. 

Please observe Section 2 of the Service Plan .

 Illumination after 

use 

The illumination (decorative) may be switched on or off if the 

timer signal is not active by pressing the key sequence 

„+“... „–”... “+“ of the body fan. 

You have to press the individual buttons within a period of 1 sec.

Please also bear in mind the possibility of defi ning two different 

illumination cycles for each day of the week (see 8.2  Service 

level I).

Error message  

„Abluft“ 

(exhaust air)

This error message is shown in the display and can be 
acknowledged by pressing the „Stop“ key. 
But before doing so, service people should repair the defect. 
Possible reasons of this message can be: 

•  the temperature in the apparatus is too high or
•  the exhaust vent system is defective 

For more information see 8.5

Summary of Contents for 7000



























































Reviews: