manualshive.com logo in svg

Kaysun Prodigy Pro AKAY-P 26 DR9, Installation & Owner'S Manual, Page: 21 / 41

Share
Download
Kaysun Prodigy Pro AKAY-P 26 DR9 Installation & Owner'S Manual Download Page 21

Indoor

Wall

Outdoor

Correct orientation of Mounting Plate

 Page 21 

Step 3: Drill wall hole for connective piping

1.  Determine the location of the wall hole based on the 

position of the mounting plate. Refer to Mounting 
Plate Dimensions.

2.  Using a 65mm or 90mm (depending on models) core 

drill, drill a hole in the wall. Make sure that the hole is 
drilled at a slight downward angle, so that the outdoor 
end of the hole is lower than the indoor end by about 
5mm to 7mm. This will ensure proper water drainage.

NOTE: When the gas side connective pipe is 

Ø

16mmor more, 

the wall hole should be 90mm.
3.  Place the protective wall cuff in the hole. This protects 

the edges of the hole and will help seal it when you finish 
the installation process.

CAUTION

When drilling the wall hole, make sure to avoid wires, 

plumbing, and other sensitive components.

MOUNTING PLATE DIMENSIONS

Different models have different mounting plates. For 

the convenience of installation, there are bubble level, 

carved dimensions on the mounting plate. Please install 

the plate and drill wall hole according to the information 

of the mounting plate. See the figures below.

Unit: mm(inch)

CAUTION:  The Bubble level on the mouting plate can't be 

removed. If it is broken, make sure to clean up the leaking 

liquid.

Horizontal direction ruler

Vertical direction 

ruler

Indoor unit outline

Indoor unit outline

Indoor unit outline

Model B

Model C

pipe hole

pipe hole

pipe hole

pipe hole

pipe hole

pipe hole

Model A

Summary of Contents for Prodigy Pro AKAY-P 26 DR9










































Reviews:

No comments