manualshive.com logo in svg

KAYO MOTOR AT125-B, Service Manual

Share
Download
KAYO MOTOR AT125-B Service Manual Download Page 34

ZHE JIANG KAYO MOTOR CO., LTD

 

 

www.RideKayo.com

 

 

34 

bearings, ball joints, a-arm bushings. 

Replace if worn or damaged.

   

 
 

 

 

  

 

Front wheel size

 

On  a  level  surface  with  handle  bars  straight  check  the  front  wheel  toe-in.  The  front 
wheel relative to the forward direction of the vehicle is: A in front and B behind the 
wheel 

Toe-in specification

：

B-A=4 ~ 10mm

 

 

 

If  not  in  this  range,  adjust  steering  rods,  adjust  the  wheel  toe-in  to  within  4~10mm, 

and lock into place. 

Note: after the adjustment of front toe-in, drive the vehicle slowly and make sure 

vehicle  tracks  straight  and  true.  After  test  ride  check  measurement  again  to 

make sure toe in is locked into place.

 

Tire pressure

 

Check the tire pressure with a tire pressure gauge. (pressure range: 4~6PSI) 

 

Note: Check the tire pressures while the tire is cool. If tire pressure is out of 

specification please adjust to within range specified. Riding with tires out of 

specified range will affect vehicle handling and may cause premature wear and 

or damage to tire tread.

 

 

 

Summary of Contents for AT125-B

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands