background image

― 

1

  ―

 

 

     

                                                                                                             

 

   

 

Gust  Blower  U2G  Type

 

Instruction Manual 

(Original Instructions) 
 

Thank you for purchasing the Gust Blower. 

This instruction manual provides information for the  customer to safely use this blower. 

Always read this manual thoroughly and fully comprehend the contents before starting work. 

Please keep this instruction manual in a handy place  for quick reference. 

                                                                           

 

<    Contents    > 

1    Introduction  ・  ・  ・  ・  ・  ・  2     

7      Operation    ・  ・  ・  ・  ・  ・  ・  ・  12 

2    Specifications  ・  ・  ・  ・  ・    2     

8      Maintenance and Inspection  ・  ・  15 

3    Product Configuration  ・  ・  6     

9      Troubleshooting  ・  ・  ・  ・  ・  ・  16 

4    Installation  ・  ・  ・  ・  ・  ・    7   

10      Warranty  ・  ・  ・  ・  ・  ・  ・  ・  ・  18 

5    Piping  ・  ・  ・  ・  ・  ・  ・  ・    9   

11      Reference  ・  ・  ・  ・  ・  ・  ・  ・    18 

6    Electrical Work  ・

 

・  ・  ・    11 

12      Disposal    ・  ・  ・  ・  ・  ・  ・  ・    18 

 

 

     

 
1.

 

This product must never be disassembled, repaired or modified by any person   

other than a qualified repair technician. Improper repairs could result in electric   
shocks or fires. 

2.

 

Always turn the power OFF, lock it, and make sure that power is not being supplied   
before starting the maintenance service. Failure to observe this could result in electric 
shocks or injuries. 

3.

 

Connect the ground wire properly, and install a dedicated earth leakage or disconnector 
on the power supply side. Failure to observe this could result in earth leakages,   
electric shocks or fires. 

4.

 

Do not touch the blower, motor or discharged air during operation. These sections 
will be very hot, and touching them could result in burns. 

 

Read the entire user manual l to be familiar with the features of this product before operating. 

Failure to operate the product correctly can result in damage to the product, personal property, 
and cause serious injury. 

※ We will not be liable for any accidents if you do not comply with the above. 
The precautions are classified as “Warning” and “Caution” to alert of the degree of injury or 

damage that could occur if handling is mistaken.

   

In either case, these are important matters related to safety, and must be observed. 

 

Warning

  :Details which if ignored could lead to fatalities or serious injuries. 

 

             

        Caution

  :Details which if ignored could lead to personal injuries or physical damage.   

 

 

Special Notes

 

 

No

.    8750

1810 

Summary of Contents for Showa Denki U2G-70T






















Reviews: