manualshive.com logo in svg

Kaval LinkNet LNKA800-A, User Manual

Share
Download
Kaval LinkNet LNKA800-A User Manual Download Page 9

 

LinkNet™  LNKA800 RF MODULES  

!

  USER MANUAL 

DCM000000054

 

 

 

Printed:  01.05.08,16:18 

 

Revision Date:5/8/01 

   9

 

 
 

 

 

Power On Self Test (POST) 

Each system module automatically performs a self-diagnostics when inserted into 
the system Card-cage.  These tests determine that the unit is a) correctly installed in 
the Card-cage and b) not damaged in transit.  

• 

All six of the LED’s on the front panel will flash 3 times 

• 

 If the LED’s do NOT flash three times, then remove the module, check the power 

source, and re-insert the module, (See Installation Instructions). 

• 

If the card is “OK” the LED’s will continue normally. (See Normal Operation) 

• 

If there is a fault, then the Red Fault LED will remain on.  If this occurs, contact 

your KAVAL WIRELESS TECHNOLOGIES Service Representative, (See 
Warranty / RMA Procedures). 

 

The Power On Self Test is 

Not

 an RF test, it only verifies that there is power to 

the unit and that the logical circuitry is functioning.

 

 

 

 

Summary of Contents for LinkNet LNKA800-A













Reviews:

No comments

Brands by name

Popular brands

Load more brands