background image

WLAN ADSL Gateway 

       

User Manual 

20 

 

The gateway can be configured to disconnect if there is no activity for a specific period 

of time by selecting the 

Dial on demand

 check box and entering the 

Inactivity 

timeout

. The entered value must be between 1 minute and 4320 minutes. 

The 

PPP IP Extension

 is a special feature deployed by some service providers. 

Unless your service provider specifically requires this setup, do not select it. If you 

need to select it, the PPP IP Extension supports the following conditions: 

a)  It allows only one computer on the LAN.   

b)  The public IP address assigned by the remote using the PPP/IPCP 

protocol is actually not used on the WAN PPP interface. Instead, it 

is forwarded to the computer's LAN interface through DHCP. Only 

one system on the LAN can be connected to the remote, since the 

DHCP server within the ADSL gateway has only a single IP 

address to assign to a LAN device.   

c)  NAPT and firewall are disabled when this option is selected.   

d)  The gateway becomes the default gateway and DNS server to the 

computer through DHCP using the LAN interface IP address.   

e)  The gateway extends the IP subnet at the remote service provider 

to the LAN computer. That is, the PC becomes a host belonging to 

the same IP subnet.   

f) 

The ADSL gateway bridges the IP packets between WAN and LAN 

ports, unless the packet is addressed to the gateway's LAN IP 

address.   

9.  Select WAN interface as the system default gateway. Click 

Next

Summary of Contents for KW5862












































Reviews: