background image

ADSL ROUTER 

       

USER MANUAL 

 

1  Overview 

Thank  you  for  using  this  Asymmetric  Digital  Subscriber  Line  (ADSL)  router.  With  the 

asymmetric technology, this device runs over standard copper phone lines. In addition, 

ADSL allows you to have both voice and data services in use simultaneously all over 

one  phone  line.  It  is  an  ideal  solution  for  the  small  and  medium  size  business 

environment. 

This  ADSL  router  provides  a  10/100BaseT  interface  for  Ethernet  connection. 

Computers  can  connect  to  the  router  via  its  Ethernet  port  to  share  its  high-speed 

Internet access. You can connect to its port regardless of the operating system you are 

using. It receives adaptive rates up to 24Mbps and transmits 1Mbps upstream.   

 

1.1  

Features 

1.1.1 

ADSL Compliance 

  ANSI T1.413 issue 2 

  Downstream: Up to 24Mbps. 

  Max upstream speed: 1Mbps. 

  Rate Adaptive at 32 Kbps steps   

  Interoperable with all major DSLAM equipment   

1.1.2 

Standards & Protocols Conformance   

  ITU G.994.1 G.992.1(G.DMT) G.992.2(G.LITE)   

  ITU G.992.3(G.DMT.BIS)   

  ITU G.992.5   

  T1.413 

  PPPoE 

  PPPoA 

  MER 

 

Summary of Contents for KD319RI

























Reviews: