background image

 

                                                                                                                                                                                        

12                                                                                  

 

OWNERS MANUAL 

 

 

 

Troubleshooting 

 

“Compressor and fan are not running.”

 

Ensure the power cord is connected. Check if the user supplied GFCI circuit is tripped. Reset as necessary 

 

“The fan is running but the compressor is not”

 

Inspect the compressor and capacitor wiring and connections. 

 

“The compressor and fan are running, but there are no bubbles coming out of any diffusers”

 

Check for leaks in line connections and at the compressor. Check connections for tightness. 

 

“The compressor and fan are running. There are bubbles coming out of some diffusers, but not all of them.”

 

The valves in the cabinet may need to be balanced. There may be a clogged diffuser that needs to be cleared. 

The compressor may be due for a rebuild. 

 

“The compressor stops and restarts” 

 

Ensure the fan is working properly. Capacitor may need replacement. 

 

Please contact Kasco or your distributor if problems persist

 

 

Warranty 

 

Diffuser Assembly: 5 years 

Teich-Aire compressor: 2 years 

Exterior Cabinet: 5 years 

SureSink Tubing: 10 years 

 

Kasco

® 

Marine, Inc. warrants this Robust-Aire

® 

System to be free from defects in material or workmanship under 

normal use and service. The Kasco Marine, Inc. obligation under this warranty is limited to replacing or repairing 

free of charge any defective part within the warranty period. Customer shall pay shipping charges for returning 

the unit to Kasco or an Authorized Repair Center.  

 

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND ANY OTHER 

OBLIGATION OR LIABILITY WHATEVER ON THE PART OF KASCO MARINE, INC. AND IN NO EVENT 

SHALL KASCO MARINE, INC. BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES. 

 

Warranty is void if: 

 

The System is not maintained properly according to the Maintenance Recommendations supplied in 

this Owner’s Manual. 

 

The System is damaged by unauthorized tampering. 

 

Summary of Contents for Robust-Aire RA1














Reviews: