background image

5

2.  Arrange the brackets into the position shown and 
tighten down the nuts.  Once the brackets are secure, 
turn the unit back into its upright position.  

3.  Follow the instruction on the previous page 
(LED3S19 Assembly instructions) to mount the light 
kit to the brackets.

Maintenance Recommendations

• 

DO NOT attempt to open light ixtures! 

• 

Under No Circumstances should anyone enter the water 
while a fountain is operating.

• 

Please keep the original box for maintenance shipping. 

The following maintenance procedures can be utilized to 
ensure many years of quality performance from your Kasco 
Fountain and Light Kit and reduce the need for more costly 
repair work.

PROPER INSTALLATION:  Proper installation of Kasco 
equipment will include a power source with ground fault 
protection.  For Fountain models, Kasco provided control 
panels included with the unit have built-in ground fault pro-
tection.  Ground fault interrupters are a safety feature that 
can also alert you to electrical leaks in the equipment.  If 
you have repeat, consistent trips of the ground fault device, 
the equipment should be disconnected and removed from 
the water.  The power cord should be inspected for dam-
age and you should contact your distributor, or call Kasco 

6. Using the cable ties, tie each ixture cord to bottom 

leg of mounting brackets using the holes provided.  
The will act as a strain relief and will keep the cord 
from being damaged by the fountain and balance the 
unit properly. Next, cable tie the main power cord to 

the loat as shown in Fig. 10.

Fig 10

 

7. Upon installation of the assembled unit, connect 

your LED light kit to your ield installed GFCI pro

-

tected outlet and timer.

Instructions For Mounting LED6S19

Instructions for attaching brackets on the loat prior 

to mounting the light ixtures on 2 HP or larger Kasco 

units.

Parts needed:
• 

Lower loat brackets (6)

•  3/8” washers (3)

Part 1

Part 2

1.  Turn the unit upside down.  Loosen and remove the 
3/8” nuts on the three 9” bolts that are closest to the 
motor unit.  Place 2 Lower Float Brackets(Part #1) and 
one 3/8” washer(Part #2) on each of the 9” bolts over 
the bottom screen clips and replace the 3/8” nut.  

Summary of Contents for LED6S19-150













Reviews: