background image

4

the ixture.  Operating the ixtures out of water will 

damage the LED and void warranty.

2. Insert the ¼” x 1” bolt into the light mounting 

bracket.  Align the bracket to the loat bracket by plac

-

ing the bolt through the light mounting hole (mount-

ing bracket is on top of the loat bracket) as shown in 

Fig.7

Fig 7

3. Install the ¼” Flat Washer, ¼” Lock Washer and 

¼” Nut against the underside of the loat tab as shown 

in Fig. 8.  Tighten the nut until snug using the 7/16” 
wrench.

Fig 8

lat washer

lock washer

1/4” nut

4. Adjust the angle of the light as desired and tighten 
the ¼” x ½” bolts on the sides of the mounting bracket 
until snug.  For more uniform illumination, it is best to 

have all three ixtures at the same angle.

5. Repeat steps 1 through 4 for the remaining ixtures.  

Assembled light ixtures are pictured in Fig. 9.  Note 

the orientation of the lights and mounting brackets.

Fig 9

6. Using the cable ties, tie each ixture cord to bottom 

leg of mounting brackets using the holes provided.  
The will act as a strain relief and will keep the cord 
from being damaged by the fountain and balance the 
unit properly. Next, cable tie the main power cord to 

the loat as shown in Fig. 5.

Fig 5

  

 

7. Upon installation of the assembled unit, connect 

your LED light kit to your ield installed GFCI pro

-

tected outlet and timer.

Instructions for mounting LED3S19 on models:
8400VFX, 800JF, 2.3VFX, 2.3JF, 3.1JF, 3.3JF, 
5.1JF, 5.3JF, 5.1VFX, 5.3VFX, 7.3JF

1. Install the mounting brackets to the light ixtures 

as shown using ¼” lock washers and ¼” x ½” bolts.  
Hand tighten only at this time.

Fig 6

Important Note:  Installation of the LED light ix

-

tures on the above listed aerating fountain units with 
the mounting brackets oriented as shown will ensure 

proper submersion of the light ixtures.  Each ixture 

must be partially submerged in order for lights to oper-

ate properly.  Other applications for these ixtures must 

provide at least the same submersion to properly cool 

Summary of Contents for LED6S19-150













Reviews: