manualshive.com logo in svg

Kasco 2400D, Operation & Maintenance Manual, Page: 11 / 15

Share
Download
Kasco 2400D Operation & Maintenance Manual Download Page 11

DE-ICER MANUAL

10

ID Description

Qty Part #

A

2400 model propeller

1

240170

A

3400 model propeller

1

340125K

A

4400 model propeller

1

440430

B

Sacrificial anode assembly (1/2” shaft)

1

243475

B

Sacrificial anode assembly (5/8” shaft)

1

243470

C

Cage assembly (includes D & E)

1

993200

D

3/8”-16 x 1-1/4” serrated flange screw

1

840543

E

3/8”-16 serrated flange nut

1

840532

REPLACEMENT PARTS

A

B

C

D

Sealed motor unit

E

and the outside air temperature must be lower than the setting on the thermostat.) Keep in mind: the ther-

mostat may take up to 30 minutes to adjust to the outside temperature. Make sure the C-20 is not in direct 

sunlight, which would heat up the thermostat. If both are activated, the small light in the upper left hand 

corner of the control box will be lit up. To troubleshoot, you can put the C-20 in the freezer for a couple 

hours and then test it. If your outdoor temperature is cold enough, you can set up the C-20 and plug a light 

into it. Watch it throughout the evening to see if and when the light comes on. If all else fails, please contact 

Kasco for assistance. 

Back to Contents

Summary of Contents for 2400D
















Reviews:

No comments