background image

Kärcher TRS-SSG • Operators •  9.801-330.0-J

OPERA

TOR’S MANU

AL

   

PRESSURE W

ASHER

  

4

IMPORTANT TRAILER SAFETY INFORMATION

Tire Size

To maintain the trailer's carrying capacity and safety, 
purchase only the same size tires as what were originally 
supplied on the trailer.

Safety Tips

Slow down if you have to go over a pothole or other 
object in road.
Do not run over curbs and try not to strike the curb when 
parking.
For a free brochure visit: 
www. nhtsa.dot.gov

IMPORTANT: Before towing this trailer be sure to 
read the instructions and warnings supplied in this 
manual. Also read the information supplied with 
your tow vehicle so you know and understand it's 
limitations.

Never Tow the Trailer Before Checking:

• 

Coupler and latch assembly show no signs of 
wear or damage. 

• 

Coupler hitch and hitch ball are of the same  
size.

• 

Coupler and safety chains are safely secured 
to the hitch. 

• 

Check all fasteners for proper tightness.

• 

Load is securely tied down to the trailer.

• 

Wheel lug nuts are properly tightened to the 
right torque. 

• 

Wheel bearings are properly adjusted and 
maintained. 

• 

Load is within the maximum load carrying 
capacity of trailer. 

• 

Tires are properly inflated and are road worthy.

• 

All trailer lighting is working properly.

• 

Tire pressure and tire condition

• 

Wheel lugs*

• 

Bearing lube and tightness

• 

Hitch

• 

Safety chains

• 

12V running lights

• 

Distribution and security

• 

Caster up in travel position

* Check lug nuts for tightness before initial trip, at 10 
miles, 25 miles and 50 miles. Recheck every 3 months 
or 3000 miles.

NOTE: Checking all of the above steps before 
every trip is key for safety.

IMPORTANT: The load must be distributed equally 
on the bed of the trailer if possible. Heavy, concen-

trated loads may cause damage or possible failure 
of the trailer.
WARNING: Loads place on the trailer must be securely 
tied to the trailer. Always use appropriate tie downs 
designed to restrict loads from moving when properly 
attached. Failure to do so will allow shifting of the load 
causing potential trailer failure and/or loss of the load 
and personal injury.

This trailer is equipped to meet all applicable federal 
safety standards in effect the day of manufacture. Check 
local and state requirements regarding any additional 
equipment that may be required.
The addition of optional equipment to your trailer may in  
crease the total weight of your trailer package to where 
it now exceeds the maximum load carrying capacity of 
the trailer.

Tow Vehicles

WARNING: Serious injury or property damage can 
result if the total weight of your loaded trailer exceeds 
the capacity of the hitch and/or your tow vehicle.

It is very important that you know and understand the 
towing capabilities of your tow vehicle. This is especially 
true with the braking abilities of the tow vehicle. You 
should check with your authorized dealer to see what the 
capabilities are for the total towing load and the maximum 
allowable tongue weight for the vehicle you plan on using 
for towing.
It is also important that the lighting system in the tow 
vehicle has sufficient capacity support the additional 
load the trailer lighting will add to the system. A heavy 
duty flasher may be required to make your turn signals 
function properly.

Trailer Ball & Couplers

WARNING: Failure to properly engage the hitch ball in 
the coupler ball socket and securely lock the coupler 
latch mechanism can cause the trailer to become 
detached from the tow vehicle while traveling, which 
may cause serious injury or property damage.

Ball diameter for which rating (GVWR) shall not exceed 
the gross trailer weight marked on the trailer  coupler.
The hitch balls have the rated load they are capable of 
towing stamped Into the top of the ball.

Make sure the ball that you use to tow your trailer has the 
same capacity rating as the coupler.
Do not use a different size ball than the size the coupler 
is designed to use.

Class

Coupler

Ball Diameter

II

3,500# GVWR

2”

III

5,000# GVWR

2”

IV

8,000# GVWR

2 5/16"

Summary of Contents for TRS-SSG-503537 E/G































Reviews: