![background image](http://html2.mh-extra.com/html/karcher/trs-ssg-503537-e-g/trs-ssg-503537-e-g_operators-manual_4691567020.webp)
Kärcher TRS-SSG • Operators • 9.801-330.0-G
OPERA
T
OR’S MANU
AL
PRESSURE W
ASHER
20
PRESSURE WASHER MAINTENANCE
PREVENTATIVE MAINTENANCE
1. Check to see that water pump is properly
lu bri cat ed.
2. Follow winterizing instructions to prevent freeze
dam age to pump and coils.
3. Always neutralize and fl ush detergent from sys tem
after use.
4. If water is known to have high mineral content, use
a water softener in your water sys tem, or de-scale
as need ed.
5. Do not allow acidic, caustic or abrasive fl uids to be
pumped through sys tem.
6. Always use high grade quality cleaning products.
7. Never run pump dry for extended periods of
time.
8. Use clean fuel: kerosene, No. 1 fuel oil, or diesel.
Clean or replace fuel fi lter every 100 hours of
op er a tion. Avoid water contaminated fuel as it will
dam age the fuel pump.
9. If machine is operated with smoky or eye burning
ex haust, coils will soot up, not letting water reach
max i mum op er at ing temperature.
1 0. Never allow water to be sprayed on or near engine
or burner assembly or any electrical com po nent.
1 1. Periodically delime coils as per instructions.
1 2. Check to see that engine is properly lubricated.
It is advisable, periodically, to visually inspect the
burn er. Check air inlet to make sure it is not clogged
or blocked. Wipe off any oil spills and keep equipment
clean and dry.
The fl ow of combustion and ventilating air to the burn er
must not be blocked or obstructed in any manner.
The area around the pressure washer should be kept
clean and free of combustible materials, gasoline and
other fl am ma ble vapors and liquids.
MAINTENANCE AND SERVICE
Unloader Valves:
Unloader valves are preset and tested at the factory
be fore shipping. Occasional adjustment of the unloader
may be necessary to maintain correct pressure.
Adjusting Unloader Valves:
Tampering with the factory setting may cause
personal injury and/or property damage and will void
the manufacturer's warranty.
Winterizing Procedure:
Damage due to freezing is not covered by warranty.
Ad here to the following cold weather procedures when-
ev er the washer must be stored or operated outdoors
under freez ing conditions.
During winter months, when temperatures drop below
32°F, protecting your machine against freezing is nec-
es sary. Store the machine in a heated room. If this is
not pos si ble then mix a 50/50 solution of anti-freeze
and water in the fl oat tank. Turn the engine on to si phon
the anti-freeze mix ture through the machine. If com-
pressed air is avail able, an air fi tting can be screwed
into the fl oat tank by re mov ing the fl oat tank strainer
and fi tting. Then inject the com pressed air. Water will
be blown out of the ma chine when the trig ger on the
spray gun is opened.
High Limit Hot Water Thermostat:
For safety, each machine is equipped with a tem-
per a ture sen si tive high limit control switch. In the event
that the wa ter should exceed its operating temperature,
the high limit con trol will turn the burner off until the
water cools then it will automatically reset itself. The
ther mo stat sen sor is lo cat ed on the discharge side of
the heat ing coil. The ther mo stat con trol dial is located
on the con trol pan el.
Pumps:
Before running the pump check the pump crankcase
for a proper oil level. A proper oil level is indicated
by the red dot in the sightglass or between the high
and low marks on the dipstick. Use only SAE 10W-40
non detergent oil. Change the initial oil after the fi rst
50 hours and then change the oil every 500 hours or
every three months.
When draining oil, clean inside of crankcase to re move
all impurities.
CAUTION
: When operating in damp
plac es or with high temperature fl uctuations oil must
be changed immediately.
Cleaning of Coils:
In alkaline water areas, lime deposits can accumulate
rap id ly inside the heating coil. This growth is in creased
by the extreme heat build up in the coil. The best
pre ven ta tive for liming conditions is to use high qual-
ity clean ing de ter gents. In areas where alkaline water
is an ex treme problem, pe ri od ic use of Coil Condi-
tioner will re move lime and other deposits before coil
be comes plugged. (See Deliming in struc tions for use
of Coil Con di tion er.)