background image

Kärcher TRS-SSG • Operators •  9.801-330.0-G

19

 

PRESSURE W

ASHER

 

  

OPERA

T

OR’S MAN 

AL

  

98013300-21

98013300-17

98013300-19

PRESSURE WASHER SHUT DOWN AND CLEAN-UP

STORAGE

CAUTION: Al ways store your pressure washer in a 
lo ca tion where the temperature will not fall be low 
32°F (0°C). The pump in this machine is sus cep ti ble 
to permanent dam age if fro zen. FREEZE DAM AGE 
IS NOT COV ERED BY WARRANTY.

  1. Stop the pressure washer, squeeze spray gun 

trig ger to release pressure.

  2. Detach water supply hose and high pressure 

hose.

  3. Turn on the machine for a few seconds, until  

re main ing water exits. Turn engine off im me di ate ly.

  4.  Drain the gas and oil from the engine.

  5. Do not allow high pressure hose to become 

kinked.

  6.  Store the machine and accessories in a room which 

does not reach freezing temperatures.

CAUTION: Fail ure to follow the above di rec tions will 
result in dam age to your pres sure washer.

When the pres sure washer is not being operated or is 
be ing stored for more than one month, follow these 
in struc tions:

  1.  Replenish engine oil to up per level.

 2. Drain gas 

o line from fuel tank, fuel line, fuel valve 

and carburetor.

  3. Pour about one teaspoon of engine oil through 

the spark plug hole, pull the starter grip several 

times and re place the plug. Then pull the starter 
grip slow ly until you feel increased pressure which 
indicates the pis ton is on its compression stroke and 
leave it in that position. This closes both the intake 
and ex haust valves to prevent rusting of cyl in der.

  4. Cover pressure washer and store in a clean, dry 

place that is well ventilated away from open fl ame  
or sparks. 

NOTE

:

 

Use of a fuel additive, such as 

STA-BIL

®

, or an equivalent, will minimize the for mu -

la tion of fuel deposits during storage. Such ad di tives 
may be added to the gasoline in the fuel tank of the 
engine, or to the gasoline in a storage con tain er.

After Extended Storage

CAUTION: Prior to restarting, thaw out any 
pos si ble ice from pressure washer hos es, 
spray gun or wand.

Engine Maintenance

During the winter months, rare atmospheric conditions 
may develop which will cause an icing con di tion in the 
car bu re tor. If this de vel ops, the engine may run rough, 
lose power and may stall. This temporary condition can 
be overcome by defl ecting some of the hot air from the 
en gine over the carburetor area.  

NOTE

: Refer to the 

en gine man u fac tur er's manual for service and main te-
 nance of the engine.

98013300-20

STEP 1:

 Re move detergent suc tion 

tube from container and insert into 
one gallon of fresh water. Open de-
 ter gent metering valve. Pull trig ger 
on spray gun and si phon water for 
one minute.  

STEP 2: 

Turn off the engine.

STEP 3:

 Tur n  off  water 

sup ply.

STEP 5: 

En gage the spray gun safe ty 

lock.

STEP 4:

 Press trig ger to release 

wa ter pres sure.

On-Off
Switch

Safety Latch

98013300-18

Summary of Contents for TRS-SSG-503537 E/G































Reviews: