Kärcher T 350, Instructions Manual

Page: 6 / 68

– 1
Please read and comply with these origi-
nal instructions prior to the initial opera-
tion of your appliance and store them for
later use or subsequent owners.

Please observe the safety in-
structions of your high-pres-
sure cleaner.
 Only trigger the high-pres-
sure jet at the high-pressure
gun if the T-Racer is located
on the surface to be cleaned.
 There must be no persons in
the immediate vicinity of the
cleaning head.
 Beware of the recoil! Ensure
a stable position and firmly
hold the high-pressure gun
with the extension tube.

Upon completion of the
cleaning operation, switch off
the high-pressure cleaner.
When working on the T-Rac-
er, disconnect it from the
high-pressure gun as well.
 Maximum water temperature
60 °C (please observe the in-
structions for your high-pres-
sure cleaner).
When unpacking the product, make sure that no acces-
sories are missing and that none of the package con-
tents have been damaged. If you detect any transport
damages please contact your dealer.
 Illustration
1 Casing
2 Handle
3 Twist grip Power (for adjustment of the cleaning
pressure)
4 Bayonet connection with union nut
5 Extension tubes (two tubes)
6 Rotor arm
7 High-pressure nozzles (2x)
The T-Racer is ideally suited for the cleaning of floor
and wall surfaces made of different materials such as
wood, plastic, concrete, tiles, and natural stone. Use the
T-Racer for private households only.
The T-Racer can be used with the provided devices. For
the use with another device, the high-pressure nozzles
must be adapted to the high-pressure cleaner used.
eg: K 2 – K 5, Kärcher 201 – Kärcher 560
 Use grey high-pressure nozzles.
e.g.: K 6 – K 7, Kärcher 600 – Kärcher 770
 Use yellow high-pressure nozzles.
Suitable KÄRCHER high-pressure nozzles can be pur-
chased in specialist shops.

DANGER
Do not reach under the edge of the T-Racer
during operation!
HARD
For sturdy surfaces (e.g. tiles, concrete,
stone).
SOFT
For sensitive surfaces (e.g. wood).
Note : Always use Kärcher water filter (order no. 4.730-
059.0) during suction operations of the high-pressure
cleaner.
Do not operate the pressure washer at the Eco level if
you wish to achieve an optimum cleaning result.
Fasten the T-Racer to the high-pressure gun using the
extension pipes.
 Illustration
1 Press the extension pipe into the bayonet catch of
the T-Racer.
2 Turn it by 90° until it locks into place.
3 Tighten the union nut.
Repeat this process even for the other joints.
 Outdoor surfaces should be swept before the T-
Racer is used to avoid damaging the high-pressure
nozzles.
 Prior to use on sensitive surfaces (e.g. wooden sur-
faces), test the product on an imperceptible spot, in
order to promptly detect any changes in the sur-
face.
 The T-Racer is not suited for scouring or scrubbing!
 Guide the T-Racer over the surface without effort.
 Do not remain at one spot; always keep moving
during cleaning.
 Adjust the twist grip "Power" in accordance with the
surface to be cleaned.
 Illustration
몇
CAUTION
Do not run over protruding corners!
Safety instructions
Description of the Appliance
Proper use
High-pressure cleaner with nominal voltage (p)
lesser than 13 MPa (130 bar)
High-pressure cleaner with nominal pressure (p) of
13 MPa (130 bar) to 16 MPa (160 bar)
Symbols
Application
Cleaning floor surfaces
Tips for cleaning
6 EN