Kärcher SP 16.000 Dirt, Original Instructions Manual

Page: 7 / 16

English 7
Manual mode
Note
In manual mode, the pump stays switched on. The fluid
level must be at least 60 mm (SP 16000 Dirt) or 50 mm
(SP 22000 Dirt) for the pump to prime itself in manual
mode. The pump can pump up to a residual fluid height
of 25 mm (SP 16000 Dirt) or 35 mm (SP 22000 Dirt).
The specified residual fluid height is only achieved in
manual mode.
The float switch must be able to move freely.
1. Fasten the float switch in the lock pointing upwards.
Illustration H
ATTENTION
Risk of damage from dry running!
Dry running leads to increased wear on the pump.
Do not leave the pump unattended in manual operation.
In case of dry running, immediately pull the mains plug
out of the socket.
2. Plug the mains plug into a mains socket.
Finishing operation
1. Pull the mains plug out of the socket.
The device stops.
ATTENTION
Risk of damage!
Risk of damage due to dried soiling or additives.
Rinse and clean the device immediately after each use.
2. If dirty liquids or liquids with additives have been
pumped, rinse and clean the device immediately af-
ter finishing operation, see chapter
Rinsing and
cleaning .
3. Drain the device and accessories and let them dry.
Care and maintenance

DANGER
Risk of electric shock and risk of injury!
The device contains electrical and mechanical compo-
nents.
Cleaning and user maintenance may not be carried out
by children.
Rinsing and cleaning
ATTENTION
Risk of damage!
Risk of damage due to dried soiling or additives.
Rinse and clean the device immediately after each use.
1 If dirty liquids or liquids with additives have been
pumped, the device must be rinsed afterwards: Use
the device to pump clear fresh water without addi-
tives until all soiling or additives have been flushed
out of the device.
 DANGER
Risk of electric shock and risk of injury!
The device contains electrical and mechanical compo-
nents.
Always disconnect the device from the power supply
before assembling, disassembling or cleaning.
2 Pull the mains plug out of the socket.
3 Press the Quick-Connect button and remove the
connection nozzle.
Illustration C
4 Where necessary, remove residue from the hose
and on Quick-Connect.
5 Clean the outside of the device with a soft, clean
cloth and clear fresh water.
6 Drain the device and accessories and let them dry.
Service
The device is maintenance-free.
Transport
Manual transport
몇 CAUTION
Risk of injury from tripping!
There is a risk of injury from tripping on loose cables and
hoses.
Be careful of cables and hoses when moving the device.
1. Lift and carry the device by the carrying handle.
Transport in vehicles
몇
WARNING
Risk of injury, risk of damage!
Note the weight of the device during transport.
Store or secure the device in accordance with applica-
ble guidelines so that it cannot slip or be thrown around
during transport.
2. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respectively applicable guidelines.
Storage
ATTENTION
Risk of damage due to frost!
An incompletely emptied device can be damaged by
frost.
Completely empty the device and accessories before
storing them.
Protect the device from frost.
Store the device in a frost-free place and not outdoors.
몇
CAUTION
Risk of injury and damage!
The device may tip over on sloping surfaces.
Be aware of the weight of the device during storage.
1. Completely empty the pump and accessories.
2. Allow the pump and accessories to dry out.
3. Store the pump in a frost-protected place.
Troubleshooting guide
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Fault Cause Rectification
The pump is running, but
not delivering Air is in the pump. 1. Pull the mains plug out of the socket and
plug it in again several times, until the fluid
is drawn in.
The suction area is clogged. 1. Pull the mains plug out of the socket.
2. Clean the suction area.
The fluid level is too low in manual oper-
ation. 1. Immerse the pump deeper into the feed flu-
id if possible, see chapter Operation .