– 8
Illustration
Turn the motor casing around and at-
tach the foam filter to the filter basket.
Insert the filter cover and turn to lock.
Install the motor casing
. Pull up on
the carrying handle to lock.
Illustration
Install the fresh water reservoir
. In-
sert the bottom part first and then press
toward the top on the motor compart-
ment to check if it is locked in.
Illustration
Attach the suction hose and the spray
hose to the connectors on the appli-
ance.
Note
: Press the suction hose tightly into the
connector to lock it into place.
Illustration
Connect the spray/suction pipes and at-
tach to the handle. Center the locking
lever when attaching it, turn clockwise
to lock.
Attach the floor nozzle to the spray/suc-
tion pipes and secure with locking lever.
The appliance is now prepared for wet
cleaning.
Caution
Always work with an inserted foam filter
- during wet as well as dry vacuum
cleaning!
Caution
Check the object to be cleaned prior to us-
ing the appliance in an inconspicuous place
for colour fastness and water resistance.
Do not clean water-sensitive floor cover-
ings such as wood floors (the moisture
could penetrate and damage the floor).
Note
Warm water (max. 50°C) will increase the
cleaning effect.
Use the wash floor nozzle.
Work without the hard surface insert.
Please only use the carpet cleaner RM 519.
Use the wash floor nozzle.
Slide the attachment for hard surfaces
onto the spray ex floor nozzle from the
side. The bristles should point towards
the back.
Use the wash hand nozzle.
Note
: You can remove the water reservoir
to fill it or you can fill it directly on the appli-
ance.
Illustration
Flip the reservoir cover up.
Add 100 - 200 ml (volume depends on
degree of contamination) of RM 519
into the fresh water reservoir, then add
tap water - do not overfill.
Close the reservoir cover.
Illustration
Insert the mains plug into the socket.
Press the switch for suction (position I),
suction turbine is running.
Illustration
Close fully the surrounding air separa-
tor at the handle.
Illustration
Press the switch for spraying (position
I), the detergent pump is ready.
Illustration
Use the lever on the spray handle to
spray on detergent solution.
Illustration
For continuous spray, the spray lever
can be locked; for this, activate the
spray lever and pull the locking key to-
ward the rear.
Run across the surface to be cleaned in
overlapping paths. Pull the nozzle back-
wards (do not push).
Operations
Wet cleaning of carpets/hard
surfaces/upholstery
Wet cleaning of carpeted floors
Wet cleaning of hard surfaces
Wet cleaning of upholstery
Fill up fresh water reservoir
Start working
15
EN
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
Summary of Contents for SE 4002
