English
13
●
The KÄRCHER NT 50/1 Mwf has a mains cable with
a PRCD-K fault current protection switch, which en-
sures that the vacuum cleaner can be used with a
power generator.
●
This device is suitable for commercial use, e.g. for
trade, industry, fire brigades and technical relief or-
ganisations.
Description of the device
Illustration A
1
Float
2
Suction hose
3
Hose hook
4
Locking the push handle
5
Crevice nozzle
6
Air exit, working air
7
Suction head
8
Suction head lock
9
Recessed grip
10
Dirt receptacle
11
Steering roller
12
Handle
13
Air inlet, motor cooling air
14
Suction hose port
15
Latch plate
16
Floor nozzle
17
Height adjustment of the floor nozzle
18
Mains plug of the device
19
Mains cable with PRCD-K circuit breaker
20
Cable holder for the disposal pump
21
Suction pipe
22
Mains plug for the disposal pump
23
Socket
24
Turn switch
25
Tool box end stop
26
Carrying handle
27
Filter cover
28
Fastening eyelet
29
Suction pipe holder
30
Push handle
31
Pre-filter
32
Float switch for the disposal pump
33
Disposal pump
34
Union nut for the disposal pump
35
Angle piece
36
Floor nozzle holder
37
Drain hose
38
Cap (GEKA-C coupling 1 1/4”)
39
Suction control (3-stage)
40
Filter frame
41
Coarse dirt filter / flat fold filter / candle filter
42
Type plate
Preparation
1. Unpack the device and install the accessories.
Illustration B
Initial startup
Only applies when operating without a power generator:
It is recommended that this device only be connected to
a socket that is protected by a 30 mA error current cir-
cuit breaker.
몇
CAUTION
Danger from sharp edges
Risk of injury
Wear suitable gloves when handling the pre-filter.
Operating modes
1 Wet vacuum cleaning with disposal pump
2 Wet vacuum cleaning without disposal pump
3 Dry vacuuming
Wet vacuum cleaning
Note
Wet vacuuming is also possible when the disposal
pump is switched off or removed. Remove disposal
pump, see dry vacuuming.
Installing the squeegees
1. Remove the brush strip.
Illustration C
2. Install the squeegees.
Removing the fleece filter bag
●
The fleece filter bag (special accessory) must al-
ways be removed when vacuuming fluids or wet
substances.
1. Unlock and remove the suction head.
2. Pull the fleece filter bag (special accessories) out to
the rear.
Illustration D
3. Fold in the lock latch and seal the fleece filter bag
tight (special accessories).
4. Fit and lock the suction head.
Removing the dust bag
●
The dust bag (special accessories) must always be
removed when vacuuming fluids or wet substances.
1. Unlock and remove the suction head.
2. Fold up the dust bag (special accessories).
Illustration E
3. Open the dust bag (special accessory) by pulling
back the suction hose port.
4. Close the dust bag (special accessory) tightly with
the closing strip underneath the opening.
5. Take out the dust bag (special accessories).
6. Fit and lock the suction head.
Installing the coarse dirt filter
1. Open the filter cover.
2. Flat fold filter only: Remove the filter frame. Remove
the flat fold filter (optional accessory) from the filter
frame.
Illustration F
Summary of Contents for NT 50/1 Mwf
