Kärcher LBB 1060/36 Bp, Manual

Page: 20 / 276

20 English
Rechargeable battery pack
The device can be operated with two 36 V Kärcher Bat-
tery Power+ battery packs.
Installation
Device assembly
몇 WARNING
Risk of injury due to incompletely assembled de-
vice
Only operate the appliance once it is fully assembled
and functional.
1. Mount the bellows on the casing.
a Push one end of the bellows over the casing pipe
so that the raised burr on the pipe fits securely in-
to the slot on the bellows.
Illustration B
b Insert the sheathed cable into the recess in the
pipe clamp.
c Fit the parts of the pipe clamp on the pipe above
and below the bellows so that the sheathed cable
is not pinched.
d Insert a screw in the pipe clamp on the side that
is closest to the device and tighten with the sup-
plied assembly tool.
Illustration C
e Insert the second screw in the other side of the
pipe clamp and tighten with the assembly tool
provided.
2. Mounting the connection pipe on the bellows.
a Push the connection pipe into the bellows so that
the raised burr on the pipe fits securely into the
slot on the bellows.
Illustration D
b Insert the sheathed cable into the recess in the
pipe clamp.
c Fit the parts of the pipe clamp on the pipe above
and below the bellows so that the sheathed cable
is not pinched.
d Insert a screw in the pipe clamp on the side that
is closest to the device and tighten with the sup-
plied assembly tool.
Illustration E
e Insert the second screw in the other side of the
pipe clamp and tighten with the assembly tool
provided.
3. Mount the blower pipe nozzle.
a Slide the cutouts on the nozzle over the lugs on
the blower pipe.
Illustration F
b Turn the nozzle so that the two arrows point to-
wards each other.
The nozzle is latched in position.
4. Mount the blower pipe.
a Slide the cutouts on the blower pipe over the lugs
on the device.
Illustration F
b Turn the blower pipe so that the two arrows point
towards each other.
The blower pipe is latched in position.
Changing the position of the handle
The position of the handle can be adjusted to the needs
of the operator.
1. Change the position of the handle.
Illustration G
a Release the locking screw.
b Slide the handle on the pipe.
c Tighten the locking screw.
Operation
몇 WARNING
Risk of injury due to incompletely assembled de-
vice
Only operate the appliance once it is fully assembled
and functional.
몇 CAUTION
Risk of injury from objects flying about
Wear safety goggles and suitable protective gloves for
all work with the device.
Control elements
The leaf blower has the following control elements:
 A power switch for switching the device on and off.
The speed is regulated via the power switch, de-
pending on how strongly it is pressed.
 A lever for fixing the speed to set the speed of the air
flow.
 A turbo boost button to maximise the air speed that
has been set via the speed fixing function. The
boost mode remains active for 2 minutes, then auto-
matically returns to normal operation.
 A locking screw to change the position of the han-
dle.
Inserting the battery pack
ATTENTION
Dirty contacts
Damage to the device and battery
Check the battery mount and the contacts for soiling
and clean them as necessary before inserting the bat-
tery.
Illustration H
1. Push the battery pack into the respective mount in
the device until it audibly latches into place.
Donning the carrying harness
Note
The carrying harness must be worn over both shoul-
ders.
1. Adjust the height of the click fastener by moving the
buckles on the belt.
2. Snap the belt click buckle into place.
3. Pull the strap ends tight so that the harness fits
snugly.
Switching on the device
몇 CAUTION
Risk of injury from flying parts and hearing damage
due to noise
Always wear eye and hearing protection.
1. Insert the battery pack, see chapter Inserting the
battery pack.
2. Press the trigger.
Illustration I
3. Fix the speed.
Illustration J
a Use the speed fixing function to adjust the
amount of airflow.
b If necessary, press the turbo boost button for
maximum flow speed.
Removing the battery pack
Note
During longer work breaks, remove the battery pack
from the device and secure it against unauthorised use.