![background image](http://html1.mh-extra.com/html/karcher/k-4000-m/k-4000-m_manual_4256537011.webp)
English
11
Definition of abbreviations used
:
HP = High pressure
DT = Detergent
When unpacking the product, make sure that no
accessories are missing and that none of the
package contents have been damaged. If you
detect any transport damages please contact
your dealer.
Illustrations on Page 2
1
ON/OFF switch for appliance
2
Power cable with plug
3
HP outlet
4
HP hose
5
Trigger gun with safety catch
6
Connection for water supply with filter
7
Coupling element for water connection
8
DT tank
9
DT suction hose with filter
10 Accessory mount, trigger gun
11 Accessory mount, HP hose
12 Accessory mount, spray lance
13 Transport handle
14 Spray lance with pressure regulation (Vario
Power)
15 Spray lance with dirt blaster
When the appliance is delivered, the HP hose
and trigger gun are not attached, this prevents
buckling. Please mount these before using the
appliance for the first time.
Î
Push out the safety clip in the trigger gun us-
ing e.g. a small screwdriver.
Î
Join HP hose and trigger gun together.
Î
Push clip in until it engages and check that it
is securely fastened by pulling on the HP
hose.
Î
Remove cable tie and unroll HP hose
For connection values, see type plate/technical
data.
Observe regulations of water supplier.
Î
Use a fibre-reinforced hose (not included)
with a standard coupling: - Minimum diame-
ter, 1/2 inches (13 mm). - Minimum length,
7.5 m.
Î
Screw the coupling unit (supplied) to the wa-
ter connection on the appliance.
Î
Push the water supply hose onto the cou-
pling unit, then connect it to the tap.
몇
Caution
Never operate the high-pressure cleaner when
the tap is turned off as dry running will damage
the HP pump.
If the water supply is not clean, the Kärcher water
filter must be used (special accessory - order No.
4.730-059).
The appliance is not suited for use in
the drinking water supply network. It is
necessary to install a suitable system
separator from Kärcher, if the device is
to be used in the drinking water supply network.
When fitted with the appropriate accessories,
this high-pressure cleaner can draw in surface
water, e.g. from water butts or ponds (max. suc-
tion height 0.5 m).
Î
Use the Kärcher water filter to protect the HP
pump and accessories (special accessories,
order no. 4.730-059). This filter removes dirt
from incoming water.
Î
As the standard coupling system is not suita-
ble for use in suction mode, the Kärcher suc-
tion hose with integrated filter should be used
instead (special accessory, order no. 4.440-
238) and suspended inside the water butt.
Î
Remove air from appliance before operation:
Switch on the appliance when the HP hose is
not connected and run it until the water which
discharges from the HP outlet is free of bub-
bles. Switch off appliance and connect HP
hose.
Note
: Fill suction hose with water before use,
this will help ventilate the pump of air.
Î
Screw HP hose on to HP outlet on appliance.
Î
Push the appropriate spray lance on to the
trigger gun and fasten it by turning it to the
right through 90°.
Î
Open tap.
Î
Plug in mains plug.
Î
Set main switch to “I/ON”.
Î
Press safety catch on the trigger gun to re-
lease it and pull lever.
Commissioning and operation
Description of the Appliance
Initial start-up
Water supply
Water supply from mains
Drawing in water from open reservoirs
Start up
Summary of Contents for K 4000 M
Page 2: ...2 ...
Page 151: ...151 ...