Kärcher K 2 Basic, Operating Instructions Manual

Page: 8 / 24

8 English
The scope of delivery of your appliance is illustrated on
the packaging. Check the contents of the appliance for
completeness when unpacking.
In the event of missing accessories or any transport
damage, please contact your dealer.
 Fabric-reinforced water hose with commercially
available coupling.
– Minimum diameter, 1/2 inches (13 mm).
– Minimum length 7.5 m.
This high pressure cleaner is designed for domestic use
only.
–
for cleaning machines, vehicles, buildings, tools,
facades, terraces, gardening tools, etc. by means
of a high-pressure water jet (if necessary, with ad-
ditional cleaning agents).
– with accessories, replacement parts and cleaning
agents approved by KÄRCHER. Please observe
the information accompanying the cleaning agents.
Notes about the ingredients (REACH)
You will find current information about the ingredients
at:
www.kaercher.com/REACH
Mount loose parts delivered with appliance prior to start-
up.
Illustrations on Page 8
Illustration
 Attach the carrying handle.
Illustration
 Pull out the clamp for the high pressure hose from
the hand spray gun.
Illustration
 Connect high pressure hose to trigger gun.
 Push the clamp in until it locks. Check the secure
connection by pulling on the high-pressure hose.
Abbildung
 Screw the coupling element to the water connec-
tion on the appliance.
 Park the appliance on an even surface.
Illustration
 Connect the high pressure hose to the high pres-
sure connection of the appliance.
 Insert the mains plug into the socket.
For connection values, see type plate/technical data.
Observe regulations of water supplier.
ATTENTION
Impurities in the water can damage the high-pressure
pump and the accessories. For protection, the use of
the KÄRCHER water filter (optional accessory, order
no. 4.730-059) is recommended.
 Attach the water supply hose to the coupling on the
water connection.
 Connect the water supply hose to the water supply.
 Completely open the water tap.
몇
CAUTION
Dry runs lasting longer than two minutes lead to damag-
es to the high pressure pump. If the appliance does not
build up pressure within two minutes, switch it off and
proceed as instructed in the Chapter "Troubleshooting".
몇
CAUTION
Keep a distance of at least 30 cm when using the jet for
cleaning painted surfaces to avoid damage.
ATTENTION
Car tyres, paint or sensitive surfaces such as wood
should not be cleaned with the dirt blaster, as there is a
risk of damage.
Illustration
 Push the spray lance into the trigger gun and fasten
it by turning it through 90°.
 Turn on the appliance “I/ON”.
 Unlock the lever on the trigger gun.
 Pull on the lever of the trigger gun; the device will
switch on.
Note: Release the lever of the trigger gun; the de-
vice will switch off again. High pressure remains in
the system.
Note: Detergent can only be added when the device is
operated in low pressure mode.

DANGER
When using detergents, the material data safety sheet
issued by the detergent manufacturer must be adhered
to, especially the instructions regarding personal pro-
tective equipment.
 Pull detergent suction hose as far as is required out
of the housing.
 Suspend end of detergent suction hose in a con-
tainer filled with detergent.
 Detach spray lance from the trigger gun. Work only
with the trigger gun.
Note: This will mix the detergent with the water stream.
 Spray the detergent sparingly on the dry surface
and allow it to react, but not to dry.
 Spray off loosened dirt with the high pressure jet.
Scope of delivery
Additionally required
Proper use
Environmental protection
The packaging material can be recycled. Please
arrange for the environmentally appropriate dis-
posal of the packaging.
Old appliances contain valuable recyclable mate-
rials that should be recycled properly. Please ar-
range for the environmentally appropriate disposal
of the old devices.
Cleaning operations which produce oily waste wa-
ter, e.g. engine washes, underbody washes, may
only be carried out using washing stations
equipped with an oil separator.
Work with detergents must only be performed on
liquid-tight work surfaces with a connection to the
sewer system. Do not let release detergent into
waters or earth.
Assembly
Start up
Water supply from mains
Operation
High pressure operation
Operation with detergent
Recommended cleaning method