background image

English

 9

You can rectify minor faults yourself with 
the help of the following overview. 
If in doubt, please consult the authorized 
customer service.

Danger

Turn off the appliance and remove the 
mains plug prior to any care and mainte-
nance work.
Repair works may only be performed by the 
authorized customer service.

Î

Pull on the lever of the trigger gun; the 
device will switch on.

Î

Check whether the voltage indicated on 
the type plate corresponds to the volt-
age of the mains supply.

Î

Check the mains connection cable for 
damages.

Î

Check setting at the spray lance.

Î

Appliance ventilation: Switch the appli-
ance on with the high-pressure hose 
detached and operate (max. 2 minutes) 
until the water exits the high-pressure 
connection without bubbles. Switch off 
appliance and reconnect high-pressure 
hose.

Î

Check the water supply.

Î

Pull out the sieve in the water connec-
tion using flat-nose pliers and clean un-
der running water.

Cause: Voltage reduction due to weak 
mains supply or when using an extension 
cable

.

Î

When switching on, first pull the lever of 
the trigger gun and then switch the ap-
pliance switch to "I/ON".

Î

Clean high-pressure nozzle: Remove 
dirt and debris from the nozzle bore, us-
ing a needle and rinse through with wa-
ter from the front.

Î

Check water flow quantity.

Î

Slight leakage from the appliance pump 
is normal. If the leakage increases con-
tact the authorized customer service.

Î

Detach spray lance from the trigger 
gun. Work only with the trigger gun.

Î

Clean the detergent suction hose filter.

Î

Check the detergent suction hose for 
kinks.

KÄRCHER UK Limited operate a helpline 
allowing customers to discuss any prob-
lems experienced with our products.
The helpline operates during normal busi-
ness hours and may be busy at peak peri-
ods.If you have difficulty getting through we 
would ask that you try to contact us again 
later in the day.

The helpline number is 01295 752200, 
open from 8.30 am to 5.00 pm 
Monday to Friday. 

It helps us if you have the model number 
and data plate details to hand before mak-
ing your call so that we can assist you with 
your query more effectively.

Alternatively you may write to us at the 
address below

:

KÄRCHER UK Ltd
Kärcher House
Beaumont Road
Banbury
Oxon, OX16 1TB

or E-mail us

:

[email protected]

Troubleshooting

Appliance is not running

Pressure does not build up in the 
appliance

Appliance does not start, motor hums

Strong pressure fluctuations

Appliance is leaking

No detergent infeed

Helpline

Summary of Contents for K 2.97 M













Reviews: