– 4
Set appliance switch to desired operating mode.
Indicator lamp for operational readiness lights up.
The device starts briefly and turns off, as soon as the
working pressure is reached.
Release the trigger gun. To do so, push the safety
catch towards the back.
When activating the hand spray gun the device switch-
es back on.
Note:
If no water comes out of the high pressure nozzle,
vent pump. Refer to "Help with malfunctions - appliance
is not building up pressure".
Set device switch to desired temperature.
–
For considerate treatment of the environment use
detergent economically.
–
The detergent must be suitable for the surface to
be cleaned.
Replace the high-pressure nozzle with the included
low-pressure nozzle (brass).
With support of the detergent dose valve set deter-
gent concentration as determined by the manufac-
turer.
Note:
Recommended values at the control panel at
maximum working pressure.
Note:
If detergent is be suctioned from an external con-
tainer, route the detergent suction hose through the re-
cess to the outside.
Set temperature and detergent concentration ac-
cording to the surface to be cleaned.
Note:
To prevent damage due to too much pressure, al-
ways position high pressure ray first from a greater dis-
tance towards object to be cleaned.
–
Loosen the dirt:
Spray detergent economically and let it work for
1...5 minutes but do not let it dry up.
–
Remove the dirt:
Spray off loosened dirt with the high pressure jet.
Removal of light contaminations and clear rinse, i.e.:
Gardening tools, terrace, tools, etc.
The appliance works in the most economical tempera-
ture range (max. 60 °C).
DANGER
Scalding danger!
Set device switch to desired temperature.
We recommend the following cleaning temperatures:
–
Light contaminations
30-50 °C
–
Contaminations containing protein, i.e. in the food
processing industry
max. 60 °C
–
Vehicle cleaning, machine cleaning
60-90 °C
Secure the trigger gun. To do so, push the safety
catch towards the front.
Set dosing value for detergent to "0".
Set the appliance switch to "1" (operation with cold
water).
Open the hand spray gun and rinse the appliance
for at least 1 minute.
DANGER
Danger of scalding from hot water! After operation with
hot water, the device must be operated with opened
handgun with cold water for at least two minutes.
Shut off water supply.
Open the hand spray gun.
Switch on the pump with the power switch and al-
low to run for about 5-10 seconds.
Close the hand spray gun.
Set the appliance switch to "0/OFF“.
Pull main plug out of socket with dry hands only.
Remove water connection.
Activate hand spray gun until device is pressure
less.
Secure the trigger gun. To do so, push the safety
catch towards the front.
Lock in the steel pipe into the holder of the appli-
ance hood.
Roll up high pressure hose and electrical conduit
and hang them into the respective holders.
Note:
Do not twist high pressure hose and electrical
conduit.
ATTENTION
Risk of damage! Frost will destroy the appliance if the
water has not been completely drained.
Store in a frost free area.
If the device is connected to a chimney, the following
must be observed:
ATTENTION
Threat of damage by penetrating cold air through the
chimney.
Disconnect device from chimney when outside
temperature drops below 0 °C.
If it is not possible to store frost free, shut down device.
For longer work breaks or if a frost free storage is not
possible:
Empty detergent tank.
Drain water.
Flush device with anti-freeze agent.
Screw off water supply hose and high pressure
hose.
Screw off supply hose at boiler bottom and drain
heating spiral empty.
Operate device for max. 1 minute until the pump
and conduits are empty.
Turning on the Appliance
Adjust cleaning temperature
Operation with detergent
Cleaning
Recommended cleaning method
Operating with cold water
Eco level
Operating with hot water
Interrupting operation
After operation with detergent
Turn off the appliance
Storing the Appliance
Frost protection
Shutdown
Dump water
8
EN
