![background image](http://html1.mh-extra.com/html/karcher/hds-3-5-30-ea-cage/hds-3-5-30-ea-cage_operators-manual_654076011.webp)
HDS 505, 508, 509, 510 • 9.800-078.0 - N
11
PRESSURE W
ASHER
OPERA
T
OR’S MAN
U
AL
WARNING: Some de ter gents
may be harm ful if in haled or in-
gest ed, caus ing severe nau sea,
fainting or poi son ing. The harm-
ful el e ments may cause prop-
er ty dam age or severe injury.
STEP 1:
Connect detergent in-
jec tor to discharge nip ple on
ma chine, Connect high pres sure
hose to in jec tor with quick coupler(check to make sure
locking coupler sleeves are in proper position be fore
ap ply ing water pres sure.
STEP 2:
Use detergent de signed
spe cif i cal ly for pres sure wash-
ers. House hold de ter gents could
dam age the pump. Pre pare de-
ter gent so lu tion as re quired by the
man u fac tur er. Fill a con tain er with
pres sure wash er de ter gent. Place
the fi l ter end of de ter gent suc tion
tube into the de ter gent con tain er.
STEP 3:
Apply safety latch to spray gun trig ger. Turn
variable pressure control handle until dis charge wa ter
exits both tubes. Secure black de ter gent noz zle into
quick cou pler if you have a sin gle wand.
NOTE:
De-
ter gent can not be ap plied us ing Red, Yel low, Green or
White noz zles.
STEP 4:
With the engine run ning,
pull trig ger to op er ate ma chine.
Liq uid detergent is drawn into the
ma chine and mixed with water. Ap-
ply de ter gent to work area. Do not
al low de ter gent to dry on sur face.
THERMAL PUMP
PROTECTION
If you run the engine on your pres sure wash er for 3-5
min utes with out pressing the trig ger on the spray gun,
cir cu lat ing water in the pump can reach high tem per a-
tures. When the water reaches this tem per a ture, the
pump pro tec tor engages and cools the pump by dis-
charg ing the warm water onto the ground. This ther mal
de vice pre vents internal dam age to the pump.
CLEANING TIPS
Pre-rinse clean ing surface with fresh water. Place de-
ter gent suc tion tube di rect ly into clean ing solution and
ap ply to sur face at low pressure (for best re sults, limit
your work area to sec tions approximately 6 feet square
and always ap ply de ter gent from bottom to top). Allow
de ter gent to re main on sur face 1-3 min utes. Do not
al low de ter gent to dry on sur face. If sur face appears
to be drying, sim ply wet down sur face with fresh water.
If need ed, use brush to re move stub born dirt. Rinse at
high pres sure from top to bottom in an even sweep ing
mo tion keep ing the spray nozzle ap prox i mate ly 1 foot
from cleaning sur face. Use over lap ping strokes as you
clean and rinse any sur face. For best surface clean ing
action spray at a slight an gle.
Recommendations:
• Before cleaning any surface, an inconspicuous
area should be cleaned to test spray pattern and
dis tance for maximum cleaning results.
• If painted surfaces are peeling or chipping, use
ex treme caution as pressure washer may re-
move the loose paint from the surface.
• Keep the spray nozzle a safe distance from the
sur face you plan to clean. High pressure wash
a small area, then check the surface for dam-
age. If no dam age is found, continue to pressure
wash ing.
CAUTION - Never use:
• Bleach, chlorine and other corrosive chem i cals
• Liquids containing solvents (i.e., paint thinner,
gas o line, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the machine and will dam-
age the surface being cleaned.
RINSING
It will take a few sec onds for the de ter gent to clear.
Apply safe ty latch to spray gun. Re move black soap
noz zle from the quick cou pler. Select and in stall the
de sired high pres sure noz zle.
NOTE:
You can also stop
de ter gent from fl ow ing by sim ply re mov ing de ter gent
si phon tube from bottle.
WARNING
DETERGENTS & GENERAL OPERATING TECHNIQUES
98000780-13
Detergent
Injector
High
Pressure
Hose
98000780-14
98000780-15