![background image](http://html2.mh-extra.com/html/karcher/hd-1090/hd-1090_safety-instructions_3831689012.webp)
10
GB
1. Starting
1.3
Assembling the accessories
·
Attach the handle to the unit with the supplied
screws.
Note: If the handle is too low for you, you
can change the height as follows:
– Remove the handle and hood.
– Unscrew the fastening nut for the
detergent tank and remove the tank.
– Unscrew the carry bar from the motor
unit (three screws) and remove to the
rear.
– Turn over the carry bar so that the top
and bottom are interchanged.
– Screw the carry bar back onto the motor
unit using the three new fastening holes.
This way, the carry bar is about 85 mm
higher.
– Reattach the detergent tank, hood and
handle.
·
Attach three-way nozzle to end of spray
lance in such a way that mark (1a) on adjusting
ring is on top.
·
Attach spray lance to handgun.
High-pressure hose
A- Lever off retaining clasp on handgun with
a screwdriver.
B- Stand handgun on end and while holding it in
this position, push end of hose into pistol as
far as end stop. At the same time, make sure
that loose disc on end of hose drops all way
to bottom.
C- Push retaining clasp back into handgun.
When attached properly, hose can only be
pulled outwards by approx. 1 mm. If hose can
be pulled out further, it must have been fitted
incorrectly.
1
High-Pressure Nozzle
2
Spray Lance
3
Servopress Spray-Gun
4
Adjustment Wheel for Pressure and Flow
Regulation
5
High-Pressure Hose
6
Handle
7
Detergent Metering Valve
8
Screw Cap for Detergent Tank
9
Detergent Tank
10
Detergent Intake Hose with Filter
11
Fastening Screw for the Hood
12
Water Connection with Sieve
13
High-Pressure Connection
14
Unit Switch
15
Pressure Gauge
16
Fastening Screws for the Handle
1.1
Unpacking the unit
·
If, while unpacking, you discover damage
has been caused in transit, please inform
your dealer immediately.
·
Do not simply discard the packing materials
with the house-hold waste. Take the packing
materials to the appropriate collection areas
for recycling.
1.2
Checking the oil level
·
Unscrew both fastening screws from the left
and right side of the hood and remove the
hood.
·
Cut off the tip of the oil tank cap.
·
Check the oil level in the oil tank.
Summary of Contents for HD 1090
