background image

#9.800-085.0  •  Rev. 01/08

13

  

PRESSURE 

W

ASHER

 

OPERA

TOR’S MANU

AL

  

  ITEM 

PART NO. 

DESCRIPTION 

 

  qTy

 

9.804-64.0 

Nozzle, 150375, Yellow (51.0) 

 

1

 

 

9.804-65.0 

Nozzle, 50375, Green (51.0) 

 

1

 

 

9.804-66.0 

Nozzle, 400375, White (51.0) 

 

1

 

 

9.804-67.0 

Nozzle, 000375, Red (51.0) 

 

1

 

 

9.80-96.0 

Nozzle, 1504, Yellow (50.0) 

 

1

 

 

9.80-97.0 

Nozzle, 504, Green (50.0) 

 

1

 

 

9.80-98.0 

Nozzle, 4004, White (50.0) 

 

1

 

 

9.80-95.0 

Nozzle, 0004, Red (50.0) 

 

1

 

 

9.80-300.0 

Nozzle, 1505, Yellow (53.0) 

 

1

 

 

9.80-301.0 

Nozzle, 505, Green (53.0) 

 

1

 

 

9.80-30.0 

Nozzle, 4005, White (53.0) 

 

1

 

 

9.80-99.0 

Nozzle, 0005, Red (53.0) 

 

1

 

 

9.80-304.0 

Nozzle, 1555, Yellow (5.0) 

 

1

 

 

9.80-305.0 

Nozzle, 555, Green (5.0) 

 

1

 

 

9.80-306.0 

Nozzle, 4055, White (5.0) 

 

1

 

 

9.80-303.0 

Nozzle, 0055, Red (5.0) 

 

1

 

 

9.80-311.0 

Nozzle, Compl. QCME 6540, Brass, All 

 

1

 

 

9.80-0.0 

Wand, 18" M x 1/4" QC 

 

1

 

9.80-3.0 

Spray Gun, SK@, 3/8" Inlet 

 

1

 

Hose, See Specifications Page 

 

9.80-517.0 

Connector, 1/" L/T, 90°, Black (51.0, 5.0) 

 

 

9.80-47.0 

Cord, Service, SOWA 1/3, Coleman (51.0, 5.0) 

 

1"

 

9.80-448.0 

Conduit, Watertight, Flex, 1/" (51.0, 5.0) 

 

8"

 

9.80-773.0 

Nut, 1/4" ESNA, NC 

 

6

 

9.80-5.0 

Injector, Detergent, Assy, 3-5 GPM 

 

1

  10 

9.803-831.0 

Connector, 3/4" L/T, 90°, Black (53.0) 

 

  11 

9.80-518.0 

Strain Relief, 3/4" (53.0) 

 

1

 

 

9.80-53.0 

 Locknut, 3/4" (53.0) 

 

1

  1 

9.80-810.0 

Washer, 5/8" Flat 

 

 

  13 

9.80-776.0 

Nut, 5/16" ESNA  

 

4

  14 

9.80-759.0 

Screw, 10/3" x 1/" BHSOC, Black (51.0, 5.0, 53.0) 

 

4

  15 

9.80-450.0 

Switch,  Pos. 10V-600V, 1-3 PH Bremas (51.0, 5.0, 53.0) 

1

  16 

9.80-478.0 

Lid, Plastic, Carlon E9801 Box (51.0, 5.0, 53.0) 

 

1

  17 

9.80-477.0 

Box, Plastic, Carlon E9801, w/o Lid (51.0, 5.0, 53.0) 

 

1

  18 

9.80-436.0 

Cord, Service, 10/3 (53.0) 

 

1"

  19 

9.803-83.0 

Conduit, Water Tite, Flex 3/4" (53.0) 

 

8"

  0 

9.80-430.0 

GFCI, 40V1Ph30A, 36' 10-3 Cord (53.0) 

 

1

 

 

9.80-431.0 

GFCI, 10V 0A, w/36' 1-3 Cord (51.0, 5.0) 

 

1

 

 

9.80-43.0 

GFCI, 10V 15A, w/36' 1-3 Cord (50.0) 

 

1

  1 

9.800-016.0 

Label, Disconnect Power Supply 

 

1

ExPLODED vIEW PARTS LIST

Summary of Contents for HD 1.9/15 Ed























Reviews: