background image

 

 

 

BR/BD 550  

  New Product Information

 

 

Service-Information-

International 

No. 90/95 dated 18 Dec 1995 

 

_________________________________________________________________________________________________  

 International Service Information 

Page   8/33 

 

 

 

Unit functions 

Driving operation (battery-powere d unit) 

When the drive lever is pushed forward or backward, the unit moves in the corresponding directions. 
The drive lever also controls the driving speed. 
Braking of the machine is effected by releasing the drive lever (centre-position). If the unit is to be 
parked, the parking brake must be set and firmly engaged in the ratchet stop position. 

 

CAUTION:

 While engaged in driving operation, do not switch off the unit by means of the key 

switch. Instead, first release the drive lever, allow the machine to come to a standstill, and only then 
turn the key switch to the off position. The emergency-stop pushbutton should be activated only in 
emergency situations. 

 

Driving operation (mains-powered unit) 

The mains-powered unit is not equipped with an electric motor for driving operation. Due to the 
reduced unit weight resulting from the absence of the storage batteries used in the battery-powered 
unit version, the propulsive force of the brush rollers and/or disc brushes is sufficient to effect forward 
motion. The unit is not equipped with a parking brake. 

 

Cleaning operation 

When the cleaning head is lowered by means of the foot pedal, a microswitch automatically activates 
the brush rollers and/or disc brushes. Upon raising the cleaning head they are disabled again  in the 
same fashion. The brush contact pressure can be manually adjusted in four steps by means of a 
lever. If a brush overload is detected, the electronic control module automatically shuts off the brush 
motors, and the corresponding indicator light on the instrument panel illuminates. If this condition 
occurs, use the key switch to switch off the machine, raise the cleaning head and remove the cause 
of the overload (i.e., excessive brush contact pressure or entangled twine), and then switch on the 
machine again. On the BR 550 unit the brushes can be offset from each other in a parallel fashion in 
order to increase the width of the cleaning area from 550 mm to 700 mm. To make this adjustment, 
the clamping screw on the cleaning head must be loosened slightly.

 

 

Water supply 

The water supply control knob on the instrument panel is used to switch on the water pump while 
selecting the water feed volume for the cleaning head. When not using the unit turn the water metering 
valve to the zero position. This shuts off the water flow to the cleaning head. 

 

Vacuuming operation 

When the suction bar is lowered by means of the control lever, a microswitch automatically activates 
the suction turbine. Upon lifting the suction bar off the floor, the suction turbine will continue to run for a 
timed interval of 10 seconds in order to transport the remaining water volume still in the suction hose 
into the dirty-water tank. When the dirty-water tank reaches its full level, a float switch switches off the 
suction turbine, and a corresponding indicator light on the instrument panel illuminates. Using the 
override function of a sealed pushbutton on the instrument panel, the suction turbine can be switched 
on or off independently. The skew of the suction bar deviating from the axis of travel, as well as its 
incline can be adjusted according to the floor covering being cleaned. For the purpose of travel in the 
reverse direction, the suction bar must be raised. 

Summary of Contents for BR 550 BAT


































Reviews: