background image

MOD190 TRANSCEIVER 

 

5

Application Requirements: 

 

A)

 

Power the MOD190 

Transceiver with 3.3VDC 

nominal voltage, with 

peak current draw of 

750mA. 

B)

 

Do not remove the shield 

on the MOD190. 

C)

 

If you use something other 

than the ¼ wave 

antenna or the wire 

antenna, the unit needs 

separate approval. 

D)

 

The antenna should be 

mounted at least 20cm 

from all persons, and 

must not transmit 

simultaneously with any 

other antenna or 

transmitter, except in 

accordance with FCC 

multi transmitter product 

procedures. 

E)

 

The MOD190 is to be 

installed only in mobile 

applications. See Part 

2.1091 for definitions of 

mobile and fixed 

applications. 

F)

 

Do not operate the 

MOD190 without an 

antenna. 

G)

 

Documentations: In the 

host’s User Manual 

include the following: 

a.

 

That there are no user 

serviceable parts in 

the radio modules. 

They should not 

remove or install radio 

modules. 

b.

 

The “Instructions To 

The User” section. 

c.

 

The “Industry Canada 

Statement”. 

d.

 

Include in the manual, 

“This device is granted 

for use in Mobile only 

configurations in 

which the antennas 

used for this 

Summary of Contents for MOD190
















Reviews: