Kantech IoPass SA-500, Installation Manual

Page: 17 / 36

P r o g r a m m i n g I o P a s s™ - S t e p b y S t e p - S e l e c t i n g t h e S y s t e m L a n g u a g e
17
S e c t i o n 5 • P r o g r a m m i n g I o P a s s ™ - S t e p b y S t e p
5.1 Selecting the System Language
IoPass offers users the ability to select the System operating lan-
guage. To select the system language:
1. Enter the master password (default is [111111]), fol-
lowed by the [#] key.
2. The LCD displays the following:
1. ENROLL 2. PASSWD
3. TIMER 4. SYSTEM
3. Press [4-System]. The LCD displays:
1. ALARM 2. CHECK
3. MODE 4. OTHER
4. Press [4-Other]. The LCD displays:
1. TONE 2. DURESS
3. MORE 4. LANGUAGE.
5. Press [4-Language]. The LCD displays the current
language. For example, if the IoPass is set to display
messages in English, it will display:
ENGLISH
Press ’1’---Change
6. Press [1] until the desired language is displayed, then
press the [*] or the [#] key. The IoPass unit will start
displaying messages in the selected language.
NOTE: Pressing the [#] key brings you back to the
Welcome message (Ready for card). Pressing the [*] key
changes the display language in the selected language
without going back to the Welcome message.
5.2
Selecting the Access Mode
The access mode is the most important function of the
system.
Before you start enrolling cards, you need to
determine how access will be granted to users.
Three (3) access modes are available in the system:
• Mode “0” - Card only - DEFAULT: This mode
only requires the user to present his card to be
granted access.
• Mode “1” - Card and PIN: This mode requires that
the user presents his card and then enters his PIN on
the keypad. Make sure the keypad can be accessed
by cardholders if you are using this mode.
• Mode “2” - Card only OR main password only:
This mode will require that the user presents his card
to the reader to be granted access
OR enters his
main password using the keypad to be granted
access.
To Select an Access Mode:
1. Enter the master password (default is [111111]), [#].
NOTE: It is strongly recommended to modify the default
password before programming the unit. To modify the
master password, refer to “Managing Passwords” (page
17).
2. The LCD displays the following:
1. ENROLL 2. PASSWD
3. TIMER 4. SYSTEM
3. Press [4-System]. The LCD displays:
1. ALARM 2. CHECK
3. MODE 4. OTHER
4. Press [3-Mode]. The LCD displays:
1-ACCESS MODE
2-DOOR_INPUT
5. Select [1-Access mode]. The LCD displays:
CURRENT: MODE ? (?=0,1 or 2)
PRESS ’1’ --] CHANGE
6. Press [1] until desired mode is displayed. Pressing
this key will toggle between selections;
7. When the required mode is displayed (0, 1 or 2),
press [#] to save and exit.
5.3
Managing Passwords
Four (4) passwords can be programmed in the IoPass unit.
It is recommended to record system passwords on the
“Quick Reference Programming Table” (page 28), and
keep it in a secure location.
5.3.1 - Modifying the Master Password
The master password is used to access the programming
mode and to protect the parameters of the IoPass
controller.
To Modify the Master Password
1. Enter the master password (default is [111111]), then
[#].
2. The LCD displays the following:
1. ENROLL 2. PASSWD
3. TIMER 4. SYSTEM
3. Press [2-Passwd]. The LCD displays the following:
1. MASTER 2. MAIN
3. AUX.CR 4. GUARD
4. Press [1-Master]. The LCD displays:
Current: 111111
New:
5. Enter the new master password. This password must
be 6 characters.
6. Press [#] to save and exit.