manualshive.com logo in svg

KANSAI SPECIAL LX-SP Series, Instructions Manual, Page: 12 / 17

Share
Download
KANSAI SPECIAL LX-SP Series Instructions Manual Download Page 12

 

9

Ｌ

Ｌ

Ｘ

Ｘ

-

-

Ｓ

Ｓ

Ｐ

Ｐ

 

 

s

s

e

e

r

r

i

i

e

e

s

s

 

【

5

】

SETTING UP & OPERATING THE CONTROL BOX   

5-1 Description 

■ 

The sequin pitch (feeding amount) and skip pattern (sequin interval) are both changeable 

by operation panel setting and machine adjustment. 

■ 

Max. speed 600 rpm is available, and insures stable operation for the sequin feed. 

 

5-2 Connecting the power wire 

■ 

Power wires extend from the control box as the following figure. 

Connect both a white and a black wire to AC220V power supply. 
Connect a green wire (earth wire) to the ground. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

 

(Fig.27) 

<Caution 1.> 

The control box can be used for only 

single-phase AC220V power type. 

The different power use certainly causes 

machine failure. 

<Caution 2.> 
The earth wire must be connected to the ground. 

<Caution 3.> 
An unstable electric power supply may cause 
the machine malfunctions. 
To avoid this problem, strongly recommend to 
use the Constant Frequency Voltage Power 
Supply (CVFT), and the Uninterruptible Power 
Supply (UPS). 

Summary of Contents for LX-SP Series


















Reviews:

No comments