background image

 

 1 

    

1

SPECIFICATIONS  

1111----1 Stitch type

1 Stitch type

1 Stitch type

1 Stitch type    
JIS401 double chainstitch machines 

 
 
 
 
 

1111----2 Model

2 Model

2 Model

2 Model    

Model BX1433 

BX1033 

(single chainstitch) 

No. of needles 

33 (Maximum) 

33 needle threads (Maximum) 

No. of threads 

33 looper threads 

 

Type of tension set 

Separate type 

Puller width 

165mm 

Minimum gauge width 

4.76mm (3/16 inch) 

Maximum gauge width 

152.4mm (6 inch) 

 
 
 

2

NEEDLES & THREADING THE MACHINE   

2222----1 Needles

1 Needles

1 Needles

1 Needles    

UO113GS of Schmetz or Organ 
Select the proper needle for the fabric and thread. 
< Needles and needle size > 

Schmetz Nm75 Nm80 Nm90 Nm100 Nm130 

Organ 

# 11 

# 12 

# 14 

# 16 

# 21 

 
 

2222----2 Replacing the needle

2 Replacing the needle

2 Replacing the needle

2 Replacing the needle    

When replacing the needle, check the needle carefully 
to see that the scarf is turned to the left of the machine 
(see the illustration). 

 
 
 
 
 
 
 
 
 

 

 

 

Organ 

Schmetz 

1433P 

UO

×

113 UY

×

113 

1033P DV-K25 

 

PSM 

DV

×

57 DV

×

57 

PTV 

DV

×

57 DV

×

57 

< Note > 

When replacing the needle, be sure to turn off the 

machine.  A clutch motor continues running for a while 

after the machine is turned off. 

Therefore keep on pressing the pedal until the machine 

stops.

 

 

 

Summary of Contents for BX Series



























Reviews: