background image

3

Table of Contents

Table of Contents

1.  Introduction ..........................................................................................4

1.1  Technical Specifications ...............................................................5

1.2  Package Contents ..........................................................................5

2.  Getting to Know Your Kanguru USB Duplicator ................................6

2.1 Parts and Functions........................................................................6

2.2 Hardware Setup .............................................................................7

2.3  Navigating the User Interface .......................................................8

3.  USB Duplicator Operations .................................................................9

3.1 Synchronous Copy.........................................................................9

3.2 Asynchronous Copy.......................................................................11

4.  Device Menu Overview .......................................................................13

5.  Troubleshooting ...................................................................................17

6.  Error Codes ..........................................................................................18

7.  Notices and Safety ...............................................................................20

8.  Warranty ...............................................................................................23

9.  Tech Support ........................................................................................23

10.  RMA Procedure ...................................................................................24

Summary of Contents for U2D2-15



























Reviews: