background image

 

TEXAS HURRICANE 

ARF 

ASSEMBLY MANUAL 

 
 
 

 

Kangke Industrial USA, Inc.  65 East Jefryn Blvd.  Deer Park NY 11729 

http://www.kangkeusa.com

      E-mail:  

[email protected]

 

Tel: 1-877-203-2377   Fax: 1-631-274-3296 

 

This manual is the sole property of Kangke Industrial USA, Inc. Reproducing any part without the 
consent of Kangke Industrial USA, Inc. is a lawful violation. 

Warranty: 

Kangke Industrial USA Inc. guarantees the kit to be free of defects in both material and workmanship at the date of 

purchase. This warranty does not cover any parts damaged by use or modifications. In no case shall Kangke Industrial’s liability 
exceed the purchase cost of this kit. Since Kangke Industrial has no control of final assembly and material used by user for final 
assembly, no liability shall be assumed or accepted for any damage resulting from the use by user of final user-assembled products. 
This kit has been flight test for normal use. If the plane will be used for extremely high stress flying, the modeler is responsible for 
reinforcing the high stress points. Inspect this kit immediately after receiving it, report any missing and damaged parts within 7 
business days otherwise the claim may be denied. 

 

1

Summary of Contents for TEXAS HURRICANE
















Reviews: