manualshive.com logo in svg

KANGKE INDUSTRIAL Monocoupe 90A, Assembly Manual

Share
Download
KANGKE INDUSTRIAL Monocoupe 90A Assembly Manual Download Page 10

Install the elevator servo with the control 
horn at the rear pointing to the center of the 
fuselage 

 
The elevator is one piece and as such the 
elevator push rod does not need the “Y” 
shape.  The “Y” however results in a much 
more ridged and precise control and is 
recommended. Use the dimensions below to 
fabricate the push rod.  

 
Install the elevator push rod in the fuselage. 
Screw a clevis on each of the threaded rods. 
Adjust each clevis until everything lines up 
and install with a rubber ring. 

Install the flying wires. The wires should be 
adjusted so there is no endplay but not so 
tight as to distort the stabilizer or rudder. 
The tail section is now complete. 
 
FUEL TANK 
Assemble the fuel tank with the proper 

stopper for your fuel type. The proto-type 
uses a three-line system with two vents out 
the bottom; this will only work with gas. 
Check your engine manufactures 
instructions for the required line system. 

 
Because gas engines have fuel pumps the 
location of the fuel tank is not as important 
as it is in glow.  Use the three tank support 
sticks to place the tank at the location best 
suited for your application. The picture 
shows where it was placed in the proto-type. 
Place one stick under the tank plug, one over 
the center recess and one in the rear notch. 

 

10

Summary of Contents for Monocoupe 90A


















Reviews:

No comments

Brands by name

Popular brands

Load more brands