manualshive.com logo in svg

KanexPro SW-4X1SL18G, User Manual

Share
Download
KanexPro SW-4X1SL18G User Manual Download Page 12

KANEXPRO

 

 

SW-4X1SL18G

 

12 | 

P a g e

 

 

6. RS232 Control 

The SW-4X1SL18G provides an RS232 port for serial port control. Connect the 
switcher to the control device (e.g. PC) with an RS232 cable and set the parameters in 
the right manner. The control device can control the switcher via designed software.   

6.1 

Installation/uninstallation of RS232 Control Software 

Installation: 

Copy the control software file to the computer connected with this 

switcher. 

Uninstallation: 

Delete all the control software files in corresponding file path. 

 

6.2 

Basic Settings 

Connect this switcher with an input device and an output device. Then connect it with a 
computer, which is installed with the RS232 control software. Double-click the software 
icon to run this software. 

Here we take the software 

CommWatch.exe 

as example. The icon is shown below: 

 

The interface of the control software is shown below: 

Please set the parameters of COM number, bound rate, data bit, stop bit and the parity 
bit correctly. Only then will you be able to send command in the Command Sending 
Area. 

Baud rate: 9600                Data bit: 8                    Stop bit: 1                  Parity bit: none 

 

 

 

Summary of Contents for SW-4X1SL18G






















Reviews:

No comments

Brands by name

Popular brands

Load more brands