KanexPro 4K HDBaseT MX-HDBASE4X4-4K User Manual Download Page 32 | Manualshive

Page: 32 / 44

background image

4K HDBaseT™ 4x4 Matrix Switcher

MX-HDBASE4X4-4K 26
www.kanexpro.com

l

Controlled by PC(s) in LAN

Connect the Switcher, a router and several PCs to setup a LAN (as shown in the
following figure). Set the network segment of the Switcher to the same as the routers,
then PCs within the LAN are able to control the Switcher.

Follow these steps to connect the devices:

Step1.

Connect the TCP/IP port of the Switcher to Ethernet port of PC with twisted
pair.

Step2.

Set the PC’s network segment to the same as the Switcher’s. Please
remember the PC’s original network segment.

Step3.

Set the Switcher’s network segment to the same as the router.

Router

Internet

PC

TCP IP Port

/

Same network
segment as the
switcher

«
...
30
31
32
33
34
...
»

Summary of Contents for 4K HDBaseT MX-HDBASE4X4-4K













































Reviews:

No comments

Related manuals for 4K HDBaseT MX-HDBASE4X4-4K

852-112/000-001

Brand: WAGO Pages: 30

Brand: Black Box Pages: 2

SRS Lighting DTS16F-DIN

Brand: plasa Pages: 4

Brand: Erbe Pages: 118

S12500G-AF Series

Brand: H3C Pages: 105

CRSMEO-4 Series

Brand: Festo Pages: 16

3C17205 - SuperStack 3 Switch 4400 PWR

Brand: 3Com Pages: 90

BNI EIP-950-000-Z009

Brand: Balluff Pages: 12

SEHI SEHI100TX-

Brand: Cabletron Systems Pages: 75

Brand: Moxa Technologies Pages: 7

Brand: TRENDnet Pages: 2

Brand: nedis Pages: 24

Brand: Pakedge Device & Software Pages: 14

Brand: Kramer Pages: 2

DCRS-5200 Series

Brand: Digital China Networks Pages: 4

Brand: WELLTECH Pages: 280

Brand: Datavideo Pages: 90

Guardian Line Series

Brand: IDEM SAFETY SWITCHES Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands