background image

 

KANE501C Manual 

Page 11

 

 

4. Glossary 

 
4.1  Selector and Display Parameters on KANE501C 
 

2Er0

” – Analyser is performing the initial zero setting. 

 
CO

2

 (Carbon Dioxide) – Direct reading of the Carbon Dioxide Sensor 

displayed in percentage (%)  
 

Eff 

(Efficiency) – Calculated combustion (not appliance) efficiency based 

on measurements of CO

2

, Flue Temperature and fuel selected. The 

KANE501C calculates nett combustion efficiency and automatically 
determines if the combustion is in the condensing mode to make 
appropriate corrections. 
 

X-Air 

(Excess Air) – Excess Air is calculated for each fuel type from the 

CO

2

 measurement. It assumes that the combustion process is running 

fuel lean. It is important to make other measurements to confirm that this 
assumption is always correct. 

 
O

2

 (Oxygen) – O

2

 is calculated for each fuel type from the CO

2

 

measurement. It assumes that the combustion process is running fuel 
lean. It is important to make other measurements to confirm that this 
assumption is always correct. 
 

TFlue

 (Flue Temperature) – TFlue is a direct measurement of the 

temperature at the tip of the flue probe. This measurement is used to 
determine the net temperature for use in calculation of the combustion 
efficiency. 
 

TNet

 (Net Temperature) – Differential temperature of TFlue and ambient 

(or inlet if set) 
 

BAT

 symbol – Displays the Battery Power available. 

 
 
 
 
 
 

Summary of Contents for 501C

















Reviews: