TECHNISCHE DATEN / SPEZIFIKATION
USAGE NOTES / FUNCTION
CHECK, MAINTENANCE, CLEANING
- Pay attention to possible hazards during maintenance work
-
(pinching, tipping, bumping...)
- Periodically check the:
-
a. proper condition of the components (defective parts
-
a.
must be replaced or repaired)
-
b. correct setup of the stand (see chapter
2
and
3
)
-
c. tight fit of all screw connections
- For cleaning, use a slightly damp cloth and a non-abrasive
-
detergent
FAULT-FINDING (F) and REPAIR (R)
F: The tripod and base are not stable
F:
R: Tighten the central Allen screw
8
F: Individual leg is not stable
F:
R: Tighten the Phillips screw on the leg tube
9
F: Clamping bracket is too tight or loose
F:
R: Loosen or tighten the adjustment screw
5
F: The music desk joint is too tight or loose
F:
R: Loosen or retighten the nut of the screw connection
7.1
5. EXTENSION TUBE and WEIGHT BEARING LOAD
5.
- The extension tube can be adjusted variably.
5.
- The clamping mechanism is supported by a clamping
5.
-
bracket that is operated using a clamping lever.
5.
- The fit of the clamping bracket is preset, the user can
5.
-
adjust this setting.
5.1
By tightening the Allen screw (each time ONLY by
5.1
1/8 increments), this increases the weight bearing load
5.1
(for example: heavy binders).
5.2
The loosening of the Allen screw does decrease
5.2
the weight bearing load, but the tube glides easier.
6. HEIGHT ADJUSTMENT
6.1
Hold the extension tube
6.2
Open the clamping lever
6.3
Adjust the extension tube to the desired height; close the
6.3
clamping lever
7. ANGLE of the DESK
The tightness of the joint of the music desk can be changed
by the user, i.e. it can be loosened or tightened.
7.1
Remove the protective cap
e.7
and loosen or retighten the
7.1
locking nut
e.6
with the key
e.8
if necessary.
7.2
Hold on to the top and bottom of music desk with both
7.2
hands and adjust the angle to the desired position.
Material
Tubes, desk, joint: Steel,
powder coated, black
Connection elements: Steel, galvanized
Base, bracket clamp, joint: Polyamid (PA)
End caps: (TPE)
Load
Sheet music, books, binders, etc.
Dimensions
Root circle diameter: 535 mm; Music Desk: 500 x 320 x 56 mm
Height (bottom edge support at 45°): 760-1300 mm
Packaging
W x D x H: 805 x 535 x 165 mm
Weight
3.5 kg
Accessories
(optional)
Carrying case 11450-000-00
4. DIMENSIONS
- Height, support, space requirement
4. ABMESSUNGEN
3. MOUNTING the BASE to the BASE TUBE
3.3
Connect BASE with BASE TUBE
3.3.1
Slide the base onto the base tube up to
3.3.1
the stop.
3.3.2
Twist the base until the bars on the base
3.3.2
bottom engage in the notches of the
3.3.2
base tube (= 0 mm).
3.3.3
Now screw the base firmly to the base tube
3.3.3
using Allen screw
c.1
.
3.3.3
Use wrench
c.3
for this purpose.
3.4
DISASSEMBLY
3.4
is performed in reverse order.
6. HEIGHT
6.
ADJUSTMENT
7. ANGLE of the DESK
FAULT-FINDING and REPAIR
5. EXTENSION TUBE
5.
and WEIGHT
5.
BEARING LOAD
